Buku Panduan Mesin Las Telwin Bimax 152 Turbo MIG-MAG

1. Bubuka

This manual provides essential information for the safe and effective operation, setup, and maintenance of your Telwin Bimax 152 Turbo MIG-MAG Welder. This machine is designed for both FLUX (no gas) and MIG-MAG (gas) wire welding processes. It features thermostatic protection for enhanced safety and durability.

Please read this manual thoroughly before operating the welder to ensure proper usage and to prevent injury or damage to the equipment.

2. Produk Langkungview

The Telwin Bimax 152 Turbo is a compact and portable wire welder, equipped with wheels and a handle for easy transport. The front panel provides access to controls and connections necessary for welding operations.

An image showing the red Telwin Bimax 152 Turbo welder unit with its control panel, wheels, handle, and the attached MIG torch and ground clamp.

Komponén konci:

• Unit Utama: The red housing containing the welding power source and wire feeder.
• Panél kontrol: Located on the front, featuring regulation knobs and switches.
• MIG Torch (TW160): For delivering welding wire and shielding gas (if applicable) to the weld area.
• Taneuh Clamp: For establishing an electrical connection to the workpiece.
• Roda sareng Gagang: Pikeun gampang dibawa.

Fitur Panel Kontrol:

• Kenop Regulasi: Adjusts welding current/voltage settings (4 positions).
• GAS/NO GAS Switch: Selects between MIG-MAG (gas) and FLUX (no gas) welding modes.
• Saklar kakuatan: Ngahurungkeun sareng mareuman mesin las.
• Thermostatic Protection Indicator: Illuminates when the unit overheats, indicating a temporary shutdown.

3. Setélan

Proper setup is crucial for safe and effective welding. Follow these steps carefully:

3.1 Sambungan Daya

• Ensure the welder is connected to a single-phase 230 V, 50/60 Hz power supply.
• Verify that the power outlet is adequately fused (16 A recommended).

3.2 Pamasangan kawat

Install the appropriate welding wire according to your material and welding process:

• Steel Welding Wire: 0.6 - 0.8 mm diameter.
• Stainless Steel Welding Wire: Diaméterna 0.8 mm.
• Aluminum Welding Wire: 0.8 - 1 mm diameter.
• Flux-Cored Welding Wire: 0.8 - 1.2 mm diameter.

Follow the internal diagrams for correct wire feeding and tension adjustment.

3.3 Gas Connection (for MIG-MAG Welding)

• For MIG-MAG welding, connect the appropriate shielding gas cylinder to the welder's gas inlet.
• Ensure all gas connections are secure and leak-free.
• Set the GAS/NO GAS switch to the 'GAS' position.

3.4 Polarity Inversion (for FLUX Welding)

When using FLUX (no gas) wire, it is often necessary to invert the polarity of the torch. Refer to the internal wiring diagram or specific instructions for your flux-cored wire to ensure correct polarity for optimal welding performance and to avoid spatter.

• Set the GAS/NO GAS switch to the 'NO GAS' position.

3.5 Accessory Connection

• Connect the MIG torch (TW160) to the designated port on the front panel.
• Ngagantelkeun taneuh clamp (Colorado 150B) to the workpiece, ensuring a clean, direct metal-to-metal contact for a good electrical circuit.

4. Parentah Operasi

Once the welder is properly set up, follow these steps for operation:

4.1 Powering On

• Hurungkeun saklar daya utama dina panel kontrol.

4.2 Nyetél Parameter Las

• Use the regulation knob to select one of the 4 available welding current/voltage positions. The optimal setting depends on the material thickness and wire diameter.
• Adjust wire feed speed as needed (usually controlled internally or via the torch trigger).

4.3 Prosés Las

• Position the MIG torch at the starting point of the weld.
• Press the torch trigger to initiate the arc and wire feed.
• Maintain a consistent travel speed and torch angle for a uniform weld bead.
• Leupaskeun pemicu pikeun ngeureunkeun las.

4.4 Thermostatic Protection

The welder is equipped with thermostatic protection. If the unit overheats due to prolonged use, the protection system will activate, and the indicator light will illuminate. The welder will automatically shut down until it cools to a safe operating temperature. Allow the unit to cool down before resuming operation.

5. Pangropéa

Pangropéa rutin mastikeun umur panjang sareng kinerja mesin las anu optimal.

• beberesih: Periodically clean the exterior of the welder with a dry cloth. Ensure ventilation openings are free from dust and debris.
• Torch and Ground Clamp: Inspect the MIG torch and ground clamp for wear or damage. Replace consumables (contact tips, nozzles) as needed. Ensure the ground clamp makes good contact.
• Kawat Pangumpan: Keep the wire feeder mechanism clean and free of dust or wire shavings. Check the wire guide and drive rollers for wear.
• Sambungan: Regularly check all electrical and gas connections for tightness and integrity.

Always disconnect the welder from the power supply before performing any maintenance.

6. Cara ngungkulan

Bagian ieu alamat masalah umum Anjeun bisa sapatemon salila operasi.

• Henteu aya kakuatan: Check the power cable, wall outlet, and the welder's main power switch. Ensure the fuse is not tripped.
• No Arc/Poor Arc:
  • Pastikeun taneuh clamp is securely attached to the workpiece and has good electrical contact.
  • Check the contact tip for blockage or wear.
  • Verify correct welding parameters (current/voltage) for the material and wire.
  • For FLUX welding, ensure correct polarity. Incorrect polarity can lead to excessive spatter and poor weld quality.
• Wire Feeding Issues:
  • Check wire spool for tangles or improper loading.
  • Ensure drive rollers are clean and have adequate tension.
  • Inspect the torch liner for blockages or kinks.
• Welder Shuts Down (Thermostatic Protection): Allow the unit to cool down. Ensure adequate ventilation around the welder. Reduce duty cycle if continuously welding for long periods.

Upami masalah tetep, konsultasi ka teknisi jasa anu mumpuni.

7. Spésifikasi

8. Kaasup Asesoris

The Telwin Bimax 152 Turbo welder typically includes the following accessories:

• Cable 16 MMQ, 1.8 M (Part No. 124502)
• Colorado 150B Ground Clamp, 150A (Part No. 712001)
• Chipping Hammer/Brush (Part No. 712139)
• TW160 MIG Torch, 2M (Part No. 742402)

9. Garansi jeung Rojongan

For information regarding warranty coverage, service, or technical support, please refer to the warranty card included with your product or contact Telwin customer service directly. Keep your purchase receipt as proof of purchase.