Émbaran Kasalametan penting
Read and understand all instructions and warnings before operating this air/hydraulic bottle jack. Failure to follow these instructions may result in serious injury or property damage. Keep this manual for future reference.
- Never exceed the rated capacity of 20 tons.
- Paké ngan dina teuas, permukaan datar.
- Ensure the load is centered on the jack saddle.
- Always use jack stands to support the load immediately after lifting. Do not rely solely on the jack for support.
- Do not work under a lifted load unless it is properly supported by jack stands.
- Anggo alat pelindung pribadi anu pas, kalebet kacamata sareng sarung tangan.
- Keep hands and feet clear of the jack and the load during operation.
- Ulah ngarobih jack atanapi nganggo éta pikeun tujuan anu sanés tibatan anu dimaksud.
- Ensure the air supply pressure is within the recommended range of 100-120 PSI.
- Inspect the jack for damage or wear before each use. Do not use if damaged.
Produk Leuwihview
The Strongway 20-Ton Air/Hydraulic Bottle Jack is designed for lifting heavy loads with both air and manual hydraulic operation. It features a 20-ton maximum lift capacity, a 1/4-inch quick-connect for air supply, a built-in bypass device, and self-returning springs for efficient operation.
Figure 1: Strongway 20-Ton Air/Hydraulic Bottle Jack. This image shows the complete jack assembly, highlighting its robust construction and air/hydraulic components.
angka 2: Tutup-up view of the Strongway 20-Ton Air/Hydraulic Bottle Jack, emphasizing its 20-ton lifting capacity.
Figure 3: The jack with its ram extended, illustrating its high-grade steel construction for durability.
Disetél
- Ngabongkar bungkusan: Carefully remove the jack from its packaging. Inspect for any shipping damage.
- Ngabersihkeun Udara: Before first use, or if the jack has been stored for a long time, purge any air from the hydraulic system.
- Puterkeun klep pelepas ka arah anu sabalikna tina jarum jam pikeun mukakeunana.
- Pump the handle several times to remove air.
- Hurungkeun klep pelepasan saarah jarum jam pikeun nutupana.
- Air Line Connection (for air operation): Connect a 1/4-inch air hose to the quick-connect fitting on the jack. Ensure your air compressor can supply 100-120 PSI.
- Posisi: Place the jack on a hard, level surface directly under the lifting point of the load. Ensure the saddle is centered.
Parentah Operasi
Lifting the Load (Hydraulic Operation)
- Pastikeun klep pelepasan ditutup pinuh ku cara muterkeunana saarah jarum jam.
- Selapkeun cecekelan kana stop kontak cecekelan.
- Pump the handle up and down to raise the jack ram and lift the load.
- Once the desired height is reached, immediately place appropriately rated jack stands under the load.
Figure 4: The jack positioned under a vehicle, demonstrating its lifting capability and versatile lift height range.
Lifting the Load (Air Operation)
- Pastikeun klep pelepasan ditutup pinuh ku cara muterkeunana saarah jarum jam.
- Connect the air hose to the quick-connect fitting.
- Activate the air control valve on the jack to begin lifting.
- Once the desired height is reached, immediately place appropriately rated jack stands under the load.
- Turn off the air control valve.
Figure 5: The jack in operation using an air hose, lifting a heavy load. This illustrates the air-powered lifting mechanism.
Nurunkeun Beban
- Ensure the area around the load is clear.
- If using jack stands, lift the load slightly off the jack stands. Remove the jack stands.
- Slowly turn the release valve counter-clockwise to lower the load. Do not open the valve too quickly, as this can cause the load to drop rapidly.
- Once the load is fully lowered, remove the jack.
Pangropéa
- Lubrication: Lumasi bagian anu bergerak sacara berkala ku oli mesin anu hampang.
- Cairan hidrolik: Check the hydraulic fluid level regularly. To check, lower the ram completely, remove the oil filler plug, and ensure the fluid is level with the bottom of the filler hole. Use only high-quality hydraulic jack oil. Do not use brake fluid or motor oil.
- beberesih: Jaga dongkrak tetep bersih sareng bébas tina kokotor, gajih, sareng bahan korosif.
- Panyimpenan: Store the jack in a dry, protected area with the ram fully retracted.
- Pamariksaan: Before each use, inspect the jack for any signs of damage, leaks, or loose parts. Do not use if any issues are found.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Jack moal angkat beban. | Leupaskeun klep; Cairan hidrolik saeutik; Udara dina sistem; Kaleuwihan beban. | Close release valve; Add hydraulic fluid; Purge air from system; Reduce load (do not exceed 20 tons). |
| Jack ngangkat barang lalaunan atawa teu teratur. | Cairan hidrolik saeutik; Hawa dina sistem; Segel geus usang. | Tambahkeun cairan hidrolik; Buang hawa tina sistem; Hubungi dukungan palanggan pikeun ngaganti segel. |
| Jack leaks fluid. | Loose fittings; Damaged seals. | Tighten fittings; Contact customer support for seal replacement. |
| Air operation not working. | Insufficient air pressure; Air line disconnected; Air control valve faulty. | Ensure 100-120 PSI air supply; Check air line connection; Contact customer support. |
spésifikasi
- model: 20-Ton Air/Hydraulic Bottle Jack
- merek: Strongway
- Kapasitas beban: 20 ton
- Minimum Lift Height: 10.25 inci
- Jangkungna Angkat Maksimum: 20 inci
- Bahan: Alloy Steel
- Beurat barang: 32.8 pon
- Rentang tekanan hawa: 100-120 PSI
- Inlet Udara: 1/4 inch quick-connect
- Fitur: Built-in bypass device, Self-returning springs
Garansi sareng Rojongan
For warranty information or technical support, please refer to the documentation included with your purchase or contact Strongway customer service. Keep your purchase receipt for warranty claims.
Pikeun pitulung salajengna, buka di Strongway Store on Amazon.