ErGear Dual Monitor Desk Mount EGCM13B Instruction Manual

Bubuka

Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.

Émbaran Kasalametan penting

Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.

• Verify that your monitor's weight and VESA pattern are within the specified limits.
• Ulah ngaleuwihan kapasitas beban maksimum 26.5 lbs per leungeun.
• Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
• Use only the provided hardware.
• Tetep bagian leutik jauh ti barudak.

spésifikasi

• model: EGCM13B
• Kasaluyuan Ukuran Layar: 13 nepi ka 34 inci
• Kapasitas Beurat (per leungeun): Nepi ka 26.5 lbs
• Kasaluyuan VESA: 75x75 mm, 100x100 mm
• Arm Span: 33 inci
• Jangkungna kutub: 16.3 inci
• Jenis gerakan: Tilt, Swivel, Rotation, Articulating
• Sudut Dengdekkeun Maksimum: 90 darajat
• Bahan: Alloy Steel
• warna: Hideung
• Tipe Pamasangan: Dudukan Méja (C-Clamp atanapi Grommet)
• C-Clamp Ketebalan Meja: 0.39" - 3.15"
• Grommet Mount Desk Thickness: 0.39" - 2.17"
• Diaméter liang grommet: 0.47" - 0.79"

Eusi pakét

Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.

• Tiang Utama nganggo Meja Clamp/Grommet Base
• Dual Monitor leungeun
• Pelat VESA (2x)
• Mounting Hardware (screws, washers, tools)
• Klip Manajemén Kabel
• Instruksi Manual

Setup sareng Instalasi

1. Desk Compatibility Check

Before installation, ensure your desk meets the following criteria:

• Bahan: Disarankeun pikeun méja kai.
• Bawah: Preferably free of beams or panels that may interfere with installation.
• C-Clamp Kandel: 0.39" - 3.15"
• Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")

2. Monitor Compatibility Check

Each monitor must meet these conditions:

• Ukuran layar: 13 nepi ka 34 inci
• beurat: Nepi ka 26.5 lbs
• VESA Pasang liang: 75x75 mm or 100x100 mm apart on the back of the monitor.

3. Assemble the Pole with Clamp Ngarojong

Choose either C-Clamp or Grommet installation based on your desk type.

Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.

4. Assemble the Arm and Pole Wire Clips

Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.

5. Assemble VESA Plate and Monitor

Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.

6. Install the Monitor to the Swivel Arm

Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).

Operasi sarta adjustment

The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewkanyamanan:

• Penyesuaian Jangkungna: Leupaskeun clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp kalayan aman.
• Dengdekkeun: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
• Putar: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewti sudut anu béda.
• Rotasi: Puterkeun monitor 360 derajat pikeun pindah antara orientasi lanskap sareng potret.
• Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.

Pangropéa

• Périodik pariksa sagala screws sareng sambungan pikeun mastikeun aranjeunna tetep kedap tur aman.
• Bersihkeun dudukan nganggo sabun anu lemes,amp lawon. Ngahindarkeun cleaners abrasive.
• Do not disassemble the mount unless instructed to do so.

Pamérésan masalah

• Monitor henteu rata: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
• Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
• Gunung karasaeun teu stabil: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.

Garansi sareng Rojongan

For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.