Buku Panduan Pangguna Mesin Pembersih Rékam Premium Pro-Ject VC-S3

1. Bubuka

The Pro-Ject VC-S3 is a premium record cleaning machine designed to effectively clean vinyl records, removing dirt, dust, and static charges. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your device. Please read these instructions carefully before first use.

2. Parentah Kasalametan

• Always disconnect the power cord before cleaning or performing any maintenance.
• Ulah ngajalankeun mesin ku leungeun baseuh atawa di lingkungan baseuh.
• Use only the recommended cleaning fluid or fluids specifically designed for record cleaning machines.
• Jauhkeun mesin tina sumber panas sareng sinar panonpoé langsung.
• Pastikeun ventilasi ditangtoskeun salila operasi.
• Jauhkeun tina jangkauan barudak.

3. Eusi Paket

Pastikeun yén sadaya barang aya dina bungkusan:

• Pro-Ject VC-S3 Rékam Mesin beberesih
• Magnetic record clamp
• Pre-mixed cleaning fluid (Wash it)
• Vacuum arm with felt strips
• Sikat bulu embe
• Kabel listrik
• Allen key for assembly

Figure 3.1: Included accessories for the VC-S3.

4. Setélan

1. Ngabongkar bungkusan: Cabut sadaya komponén tina bungkusna kalayan ati-ati. Simpen bungkusna kanggo diangkut atanapi disimpen engké.
2. panempatan: Place the VC-S3 on a stable, level surface. Ensure there is adequate space around the machine for operation and ventilation.
3. Vacuum Arm Installation: Insert the vacuum arm into its designated slot on the top plate of the machine. Ensure it is securely seated.
4. Majelis piring: Place the platter onto the motor spindle.
5. Sambungan Daya: Sambungkeun kabel listrik ka mesin teras ka stop kontak listrik anu cocog.

Gambar 4.1: Top view of the VC-S3 with platter and vacuum arm.

Figure 4.2: VC-S3 with a record on the platter.

5. Parentah Operasi

1. Rékam tempat: Place a vinyl record onto the platter. Secure it with the magnetic record clamp.
2. Apply Fluid: Apply a small amount of the pre-mixed cleaning fluid evenly across the record surface. Use the provided goat hair brush to gently spread the fluid and work it into the grooves.
3. Mimitian Motor: Flip the 'MOTOR' switch to the 'ON' position (usually indicated by 'I' or 'II' for different directions). Allow the record to rotate for a few revolutions to ensure the fluid is well distributed.
4. Engage Vacuum: Position the vacuum arm over the record. Flip the 'VACUUM' switch to the 'ON' position (indicated by 'I'). The vacuum system will activate, drawing the cleaning fluid and impurities from the record surface.
5. Dry Record: Allow the vacuum to operate for 1-2 revolutions in each direction (if applicable) until the record surface appears dry. The VC-S3 is designed for fast drying, typically within 2 rotations.
6. Remove Record: Turn off the 'VACUUM' and 'MOTOR' switches. Carefully remove the record clamp and then the cleaned record.
7. Ulang deui: Repeat the process for the other side of the record and for additional records.

Figure 5.1: Control switches for motor and vacuum.

Figure 5.2: Vacuum arm in operation on a record.

Gambar 5.3: Detil view of the vacuum arm.

6. Pangropéa

• Emptying Waste Tank: The VC-S3 features a 2.5L internal waste fluid tank. Regularly check the fluid level and empty it when full. Refer to the diagram in the full manual for the waste tank drain plug location.
• Cleaning Vacuum Arm: Periodically inspect the felt strips on the vacuum arm for wear or debris. Replace them if they become dirty or worn to ensure optimal suction and prevent scratching records.
• Bersihan Luar: Wipe the exterior of the machine with a soft, dry cloth. Avoid using abrasive cleaners or solvents.

7. Cara ngungkulan

• Record Not Drying Completely:
  • Ensure the vacuum arm is properly seated and making full contact with the record surface.
  • Check if the felt strips on the vacuum arm are clean and not overly saturated or worn. Replace if necessary.
  • Verify the waste fluid tank is not full.
  • Allow for an additional revolution or two under vacuum.
• Nyeuseup lemah:
  • Check for blockages in the vacuum arm or tubing.
  • Ensure the vacuum arm is correctly installed and sealed.
  • Empty the waste fluid tank.
• Wet Streak Under Vacuum Arm:
  • This can occur if the vacuum is turned off too quickly or if the felt strips are saturated. Allow the vacuum to run for a full rotation after the record appears dry.
  • Ensure felt strips are clean and in good condition.
• Motor Teu Muter:
  • Pariksa sambungan kakuatan.
  • Ensure the 'MOTOR' switch is in the 'ON' position.

8. Spésifikasi

9. Émbaran jaminan

Pro-Ject products are manufactured to the highest quality standards. This product is covered by a manufacturer's warranty against defects in materials and workmanship. The specific duration and terms of the warranty may vary by region. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the documentation included with your product or visit the official Pro-Ject websitus.

10. Rojongan

For technical assistance, spare parts, or further information regarding your Pro-Ject VC-S3, please contact your authorized Pro-Ject dealer or visit the official Pro-Ject Audio Systems websitus. Anjeun tiasa mendakan wincik kontak sareng sumber dukungan di Pro-Ject Audio Systems Store.