1. Bubuka
This manual provides instructions for the BENINCA TO.GO 4WV garage door opener remote control. This device is designed to operate BENINCA garage doors and gate openers using a 433.92MHz rolling code frequency. Please read this manual carefully before use to ensure proper operation and longevity of your remote control.
2. Produk Langkungview
The BENINCA TO.GO 4WV is a compact and reliable hand transmitter featuring four buttons for controlling multiple functions or devices. It utilizes rolling code technology for enhanced security.
2.1 Eusi pakét
- 1 x BENINCA TO.GO 4WV Remote Control
- 1 x Batré (parantos dipasang)
- 1 x Gantungan Kunci
2.2 Visual Produk
Gambar 1: Hareupeun view of the remote control with four white buttons.
Gambar 2: hareup lengkep view showing the LED indicator and buttons.
Gambar 3: Sisi profile tina kadali jauh.
Gambar 4: Angled view ngajéntrékeun desain ergonomis.
Gambar 5: Tukangeun view with the battery compartment cover.
Figure 6: Dimensions of the remote control (approximately 70mm x 40mm x 14mm).
2.3 Video produk
Video 1: Unboxing and demonstration of button functionality.
3. Spésifikasi
| Fitur | Spésifikasi |
|---|---|
| Modél | BENINCA TO.GO 4WV |
| Model cocog | BENINCA TO.GO 2WV, BENINCA TO.GO 4WV |
| Frékuénsi | 433.92MHz |
| Métode Encoding | Kodeu Rolling |
| Kancing | 4 |
| Batré | Kaasup |
| Asalna | Daratan Cina |
| Sertifikasi | CE |
4. Setelan sareng Pemrograman
To program your BENINCA TO.GO 4WV remote control, you will need access to your existing BENINCA receiver or opener unit. The programming procedure typically involves interacting directly with the receiver unit, not just the remote itself.
General Programming Steps (may vary by receiver model):
- Locate the Receiver: Find the control unit for your garage door or gate opener. This is usually located near the motor or inside a control box.
- Access Programming Button: On the receiver, locate the programming button (often labeled 'PROG', 'MEMO', 'LEARN', or similar). Consult your original BENINCA receiver/opener manual for its exact location and labeling.
- Activate Learning Mode: Press and release the programming button on the receiver. An LED indicator on the receiver should light up or flash, indicating it is in learning mode.
- Transmit Code from New Remote: Within a few seconds (usually 5-10 seconds), press and hold the desired button on your new BENINCA TO.GO 4WV remote control that you wish to program.
- Konfirmasi Pemrograman: The LED on the receiver should change its state (e.g., flash rapidly, turn off, or light up solid) to confirm successful programming. Release the button on the remote.
- Test Jauh: Wait a few seconds for the receiver to exit learning mode, then test the newly programmed button on your remote control to ensure it operates the garage door or gate.
Important: Always refer to the specific instruction manual for your BENINCA receiver/opener model for precise programming steps, as procedures can vary. Ensure you have access to your receiver before attempting to program the remote.
5. Operasi
Once programmed, operating your BENINCA TO.GO 4WV remote control is straightforward:
- Point the remote control towards your garage door or gate opener.
- Press the programmed button corresponding to the function you wish to activate (e.g., open, close, stop).
- The LED indicator on the remote control will light up briefly when a button is pressed, confirming signal transmission.
Figure 7: Demonstrating button press on the remote control.
6. Pangropéa
6.1 Ngagantian batré
The remote control comes with a pre-installed battery. If the remote's range decreases significantly or the LED indicator does not light up when a button is pressed, it's likely time to replace the battery.
Pikeun ngaganti batré:
- Locate the battery compartment cover on the back of the remote control (refer to Figure 5).
- Carefully open the compartment using a small screwdriver or by sliding the cover as indicated.
- Remove the old battery. Note its orientation (+/-).
- Pasangkeun batré anyar anu jinisna sami, pastikeun polaritasna leres.
- Tutup panutup kompartemen batré aman.
Warning: Dispose of old batteries responsibly according to local regulations. Keep batteries out of reach of children.
6.2 beberesih
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing atawa komponén internal.
7. Cara ngungkulan
If your remote control is not functioning as expected, try the following troubleshooting steps:
- Jauh teu tiasa dianggo saatos program: Double-check the programming steps in your receiver's manual. Ensure the receiver was in learning mode and the correct button was pressed on the remote.
- rentang operasi pondok: Replace the battery in the remote control. Ensure there are no obstructions between the remote and the receiver. Check for sources of radio interference (e.g., other wireless devices, metal structures).
- LED on remote does not light up: The battery may be dead or incorrectly installed. Replace the battery.
- Jauh dianggo intermittently: This could indicate a low battery, interference, or a loose connection inside the remote. Try replacing the battery first.
If the issue persists after trying these steps, contact customer support or a qualified technician.
8. Tips pamaké
- Keep Receiver Manual Handy: For programming and advanced settings, always refer to the instruction manual of your BENINCA garage door or gate receiver/opener. This is crucial for successful setup.
- Rentang tés: After programming, test the remote's operating range from various distances and angles to ensure reliable performance.
- Secure Your Remote: Treat your remote control like a key. Keep it in a secure location to prevent unauthorized access to your garage or gate.
9. Garansi jeung Rojongan
Kanggo inpormasi garansi, dukungan téknis, atanapi patarosan jasa, mangga tingal dokuméntasi anu disayogikeun sareng pameseran anjeun atanapi langsung ngahubungi penjual. Simpen bukti pameseran anjeun pikeun klaim garansi.
