GEPRC TAKER F722 BLS 65A V2 Stack Instruction Manual

1. Bubuka

The GEPRC TAKER F722 BLS 65A V2 Stack is a high-performance flight control system designed for RC FPV Drones. It integrates the GEP-F722-HD V2 Flight Controller and the TAKER BLS 65A 4-IN-1 ESC, offering advanced features and robust power delivery for an exceptional flying experience.

2. Fitur

• Uses the mainstream STM32F722 chip for powerful processing.
• Equipped with the latest 42688-P gyroscope for precise flight control.
• 16M onboard black box storage for flight data logging.
• Integrated LC filter for clean power delivery to sensitive components.
• Upgraded Type-C USB interface for convenient connectivity.
• Directly plugs into the DJI Air Unit for seamless digital FPV integration.
• Paired with the TAKER H65_8S_BLS 65A 4IN1 ESC for smooth and responsive flight.
• Simple and efficient installation method with shock absorbers for stable gyroscope performance.
• Dual independent BECs: 9V@2.5A and 5V@3A for powering various peripherals.

3. Spésifikasi

3.1 GEP-F722-HD v2 Flight Controller

3.2 TAKER H65_8S_BLS 65A 4IN1 ESC

4. Eusi Paket

The GEPRC TAKER F722 BLS 65A V2 Stack package includes the following items:

• 1 x FC board (Flight Controller)
• 1 x ESC board (Electronic Speed Controller)
• 1 x Kapasitor
• 1 x DJI Air Unit adapter cable
• 1 x Flight controller adapter cable
• 1 x XT60 power cable
• 4 x M3*30 screws
• 4 x M3*25 screws
• 8 x kacang nilon
• 8 x Silicone anti-shake pads
• 2 x sh1.0 4pin silicone cable
• 1 x kabel sambungan kaméra

5. Setup jeung Instalasi

Careful installation is crucial for the optimal performance and longevity of your FPV drone. Please follow these guidelines:

5.1 Pamasangan

• Ensure your drone frame has a 30.5*30.5mm mounting pattern.
• Use the provided silicone anti-shake pads to isolate the flight controller from frame vibrations. This is essential for stable gyroscope performance.
• Secure the FC and ESC boards using the M3 screws and nylon nuts. The mounting holes are designed to accommodate M3 screws, with a φ4mm hole reducing to φ3mm when using the silicone shock-absorbing rings.

5.2 Kabel

Refer to the pinout diagrams (if available in the full product documentation) for precise connections. Key connections include:

• Sambungan Daya: Connect the XT60 power cable to your LiPo battery and the ESC. Ensure correct polarity. The ESC supports 3-8S LiPo input.
• Sambungan Motor: Solder your motors to the designated pads on the 4-IN-1 ESC (M1, M2, M3, M4). Double-check motor direction in BetaFlight.
• DJI Air Unit: Utilize the dedicated DJI Air Unit adapter cable for direct plug-in connection to the flight controller.
• panarima: Connect your RC receiver to one of the 5 available UARTs on the flight controller.
• Kaméra: Use the camera connection cable to link your FPV camera to the flight controller.
• Periferal séjénna: Connect any other components (e.g., GPS, VTX, Buzzer) to the appropriate UARTs or pads, ensuring they are powered by the correct BEC output (5V@3A or 9V@2.5A).

5.3 Konfigurasi Awal

• Connect the flight controller to your computer via the Type-C USB interface.
• Open BetaFlight Configurator software.
• Flash the appropriate firmware target: GEPRCF722 for the Flight Controller and B_X_30 for the ESC.
• Configure your receiver, motors, OSD, and other settings within BetaFlight.
• Perform a motor direction test and calibrate your ESCs if necessary.

6. Parentah Operasi

Once installed and configured, your GEPRC TAKER F722 BLS 65A V2 Stack is ready for flight. Always ensure your drone is in a safe environment and clear of obstacles before arming.

• Pariksa Pra-Hiber: Verify all connections are secure, propellers are correctly installed, and battery is fully charged.
• Arming: Arm your drone using the configured switch on your remote controller.
• Modeu hiber: Select appropriate flight modes (e.g., Acro, Angle, Horizon) based on your skill level and flight conditions.
• Ngawaskeun: Utilize the BetaFlight OSD to monitor critical flight data such as battery voltage, current, and RSSI during flight.
• Ngarampas pakarang: Disarm your drone immediately after landing or in case of an emergency.

7. Pangropéa

Regular maintenance helps ensure the longevity and reliability of your flight stack.

• beberesih: Keep the boards free from dust, dirt, and debris. Use compressed air or a soft brush.
• Pamariksaan: Periodically check for loose connections, damaged wires, or signs of overheating on the ESC.
• Pembaruan firmware: Keep your flight controller and ESC firmware updated to benefit from performance improvements and bug fixes.
• Panyimpenan: Store the stack in a dry, cool environment when not in use.

8. Cara ngungkulan

Ieu sababaraha masalah umum sareng solusi poténsialna:

• Henteu aya kakuatan: Check battery connection, XT60 cable, and ensure no short circuits.
• Motor Teu Muter: Verify motor connections, ESC calibration, and motor direction in BetaFlight. Check for bent motor shafts or damaged propellers.
• Penerbangan teu stabil: Ensure silicone anti-shake pads are correctly installed. Check for loose components or incorrect PID tuning in BetaFlight.
• No OSD Display: Verify camera and OSD connections. Ensure OSD is enabled and configured in BetaFlight.
• No Receiver Input: Check receiver wiring to the FC and ensure the correct UART and receiver protocol (e.g., SBUS, Crossfire) are selected in BetaFlight.
• Masalah Sambungan USB: Try a different USB cable or port. Ensure BetaFlight Configurator is up-to-date.

9. Tips pamaké

• Always perform a dry run (without propellers) after any changes to wiring or configuration to ensure motors spin correctly and safely.
• Start with conservative PID settings in BetaFlight and tune gradually for optimal flight performance.
• Consider adding a small amount of conformal coating to the flight controller and ESC for added protection against moisture and dust, especially if flying in damp kaayaan.

10. Garansi jeung Rojongan

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty-related inquiries.