ANEX IQ Dasar Stroller
IQ ALL-IN-Hiji
Lipatan tina pigura
IQ RANGKA
Unfolding tina pigura
Ngalampirkeun tina roda hareup
Ngonci roda swivel hareup
Ngalampirkeun tina roda pungkur
Rem
Nyerep shock
Nanganan angger
Disconnecting / nyambungkeun karanjang balanja
Mawa gagang
adjustment lebar pigura
Ngabongkar momotanana
Lipetan tina carrycot
Unfolding tina carrycot
Kantétan kana pigura
Ventilasi
adjustment tiung Carrycot urang
Kantétan panutup Carrycot
beberesih Carrycot urang
Kantétan kana pigura
Unit korsi IQ
Tilepan pigura jeung korsi
adjustment tiung Unit korsi urang
adjustment backrest Unit korsi urang
Ventilasi tina sandaran unit korsi
adjustment footrest
Panghalang kaamanan unit korsi
Sabuk kaamanan ngaitkeun
adjustment sabuk kaamanan
Ngabersihan unit korsi
Softgoods assembling
adjustment tiung Buggy urang
Ventilasi tina sandaran buggy
adjustment backrest Buggy urang 
adjustment footrest
Sabuk kaamanan ngaitkeun
adjustment sabuk kaamanan
Tilepan pigura kalawan buggy
Raincover pikeun carrycot / unit korsi
Pariksa manual panganyarna dina kami websitus: anexbaby.com
Inpormasi tiasa robih tanpa aya bewara. Anex moal nanggungjawaban kanggo kasalahan téknis atanapi omissions dikandung dina manual ieu. Produk nu dibeuli bisa jadi béda ti produk sakumaha dijelaskeun dina manual ieu.
AVALEX PTE. LTD.,
8 Eu Tong Sen Street # 17-88, Tengah
Office Tower 2, Singapura, 059818
+65 62215096
office@anexbaby.com
Dokumén / Sumberdaya
 | IQ Dasar Stroller |
Rujukan
- Manual pamakémanual.tools
Dear Anex Team,
We are experiencing an issue with our Anex IQ stroller and would appreciate your assistance.
We have these height adapters that were previously attached to the frame, and we used them with the bassinet without any problems. After removing the bassinet, we installed the seat unit (stroller seat) without the adapters.
However, the height adapters are now stuck in the seat unit, and we are unable to remove them. We have tried pulling them out, but they do not come off.
Could you please advise how to safely remove these adapters? If possible, we would appreciate it if you could send us instructions or a guide.
We have attached photos for your reference.
Thank you in advance for your help.
Salam hormat,
Yuliya Tolkishevskaya
We are experiencing an issue with our Anex IQ stroller and would appreciate your assistance.
We have these height adapters that were previously attached to the frame, and we used them with the bassinet without any problems. After removing the bassinet, we installed the seat unit (stroller seat) without the adapters.
However, the height adapters are now stuck in the seat unit, and we are unable to remove them. We have tried pulling them out, but they do not come off.
Could you please advise how to safely remove these adapters? If possible, we would appreciate it if you could send us instructions or a guide.
We have attached photos for your reference.
Thank you in advance for your help.
Salam hormat,
Yuliya Tolkishevskaya
How do I remove the height adapters from the Anex IQ seat unit if they are stuck?
Removing height adapters from the Anex IQ seat unit typically requires engaging the release mechanism located on the adapters themselves or the seat unit's attachment points. If they are stuck, please try the following steps:
Awas: Do not use excessive force or tools like pliers, as this may damage the plastic locking tabs. If the adapters remain stuck, it is recommended to contact Anex customer support directly at office@anexbaby.com or visit an authorized service center, as there may be a mechanical obstruction or a need for professional lubrication of the locking pins.
Read the full Q&A page