Extech DO600 Waterproof ExStik II Dissolved Oxygen Meter User Manual

1. Bubuka

The Extech DO600 Waterproof ExStik II Dissolved Oxygen Meter is designed for precise measurement of dissolved oxygen levels. It displays oxygen concentration as a percentage of saturation (0 to 200%) or as a concentration in parts per million (ppm) or milligrams per liter (mg/L) (0 to 20.00 ppm/mg/L). Key features include adjustable altitude compensation, adjustable salinity compensation, and an analog bargraph for trend indication. This manual provides instructions for the proper setup, operation, and maintenance of your DO600 meter.

2. Eusi Paket

Pastikeun yén sadaya barang aya sareng dina kaayaan anu saé nalika ngabongkar:

• Extech DO600 Dissolved Oxygen Meter
• DO éléktroda
• Protective Sensor Cap
• Spare Membrane Cap
• Electrolyte Solution
• Four 3V CR-2032 Batteries (pre-installed or included separately)
• 48-inch (1.2m) Neck Strap

Figure 1: Extech DO600 meter with its accessories, including the electrode, caps, electrolyte, and neck strap.

3. Meter Components

Gambar 2: Hareupeun view of the Extech DO600 meter.

1. Layar LCD: Shows dissolved oxygen readings, temperature, and other indicators.
2. MODE/HOLD Button: Toggles between measurement modes and holds the current reading.
3. CAL/RECALL Button: Initiates calibration and recalls stored data.
4. Tombol ON/OFF: Powers the meter on or off.
5. Éléktroda: Sensor for dissolved oxygen measurement.
6. Protective Sensor Cap: Covers and protects the electrode.

4. Setélan

4.1. Pamasangan batré

The DO600 meter uses four 3V CR-2032 batteries. These are typically pre-installed. If replacement is necessary:

1. Twist off the battery compartment cap located at the top of the meter.
2. Remove the old batteries, noting their polarity.
3. Insert new CR-2032 batteries with the correct polarity.
4. Securely replace the battery compartment cap to maintain the waterproof seal.

4.2. Persiapan Éléktroda

Before first use or after prolonged storage, the DO electrode requires preparation:

1. Unscrew the protective sensor cap from the electrode.
2. Fill the spare membrane cap with the provided electrolyte solution. Ensure no air bubbles are trapped.
3. Carefully screw the membrane cap onto the electrode, ensuring the membrane is taut and free of wrinkles.
4. Allow the electrode to stabilize for approximately 15-30 minutes in the electrolyte solution before calibration.

5. Parentah Operasi

5.1. Daya Hurung / Pareum

Pencét éta ON/OFF tombol pikeun ngahurungkeun atawa mareuman alat méter.

5.2. Kalibrasi

Regular calibration ensures accurate readings. Calibrate the meter in air-saturated water or a known standard solution.

1. Ensure the electrode is prepared as described in Section 4.2.
2. Immerse the electrode in air-saturated water (e.g., tap water stirred vigorously for several minutes) or a DO standard solution.
3. Pencét jeung tahan tombol CAL / NGARETAK pencét tombol "CAL" nepi ka muncul dina layar.
4. The meter will automatically recognize the calibration point and adjust. Wait for the reading to stabilize and for the calibration indicator to confirm completion.

5.3. Nyandak Pangukuran

To measure dissolved oxygen:

1. Daya dina méteran.
2. Celupkeun éléktroda kana sample larutan. Pastikeun mémbran tilelep sapinuhna sareng bébas tina gelembung hawa.
3. Gently stir the electrode in the sample to ensure proper flow across the membrane.
4. Wait for the reading on the LCD display to stabilize. The display will show both dissolved oxygen and temperature.
5. Pencét éta MODE / NGANGGO button to cycle between % saturation and ppm (mg/L) readings.
6. To hold a reading, briefly press the MODE / NGANGGO tombol. Pencét deui pikeun ngaleupaskeun.

Figure 3: The Extech DO600 meter being used to measure dissolved oxygen in a laboratory.

5.4. Altitude Compensation

Dissolved oxygen saturation levels are affected by altitude. The DO600 allows for manual adjustment:

• Refer to the meter's full instruction manual for specific steps to enter and adjust altitude compensation (0 to 20,000 feet in 1,000 ft. increments).

5.5. Salinity Compensation

Salinity also influences dissolved oxygen levels. The DO600 provides adjustable salinity compensation:

• Consult the meter's comprehensive manual for detailed instructions on setting salinity compensation (0 to 50 ppt).

6. Pangropéa

6.1. Pabersihan sareng Panyimpenan Éléktroda

To maintain electrode performance:

• Bilas éléktroda ku cai sulingan sanggeus unggal pamakéan.
• If the membrane becomes fouled, gently clean it with a soft cloth or cotton swab. Replace the membrane cap if it is damaged or heavily contaminated.
• When storing, ensure the protective sensor cap is filled with electrolyte solution to keep the membrane hydrated.

6.2. Ngagantian batré

Ganti batréna nalika indikator batré lemah némbongan dina tampilan. Tingali Bagian 4.1 pikeun parentah pamasangan batré.

7. Cara ngungkulan

8. Spésifikasi

Figure 4: Physical dimensions of the Extech DO600 meter. Note: The image shows 7.7 inches, while product specifications state 6.9 inches. Refer to the latest product documentation for precise measurements.

9. Video produk

Henteu aya pidéo produk resmi ti anu ngajual pikeun barang ieu dina data anu disayogikeun.

10. Garansi jeung Rojongan

For warranty information, technical support, or to purchase accessories and replacement parts, please refer to Extech's official websitus atanapi ngahubungan departemén layanan palanggan maranéhna. Anjeun tiasa manggihan inpo nu langkung lengkep ihwal nu Toko Extech di Amazon.