Winco Stainless Steel Juice Dispenser (Model 902) Instruction Manual

1. Bubuka

Thank you for choosing the Winco Stainless Steel Juice Dispenser, Model 902. This dispenser is designed for serving various beverages such as lemonade, orange juice, and iced tea in commercial or event settings. Its durable stainless steel construction and clear polycarbonate container ensure both longevity and an attractive presentation. This manual provides essential information for the safe and efficient use, assembly, cleaning, and maintenance of your dispenser.

Fitur konci:

• Capacity: Approximately 2.2 Gallons (8.3 Liters)
• Material: Stainless Steel body, clear polycarbonate juice container
• Integrated stainless steel ice chamber to keep beverages chilled without dilution
• Dulang titisan anu tiasa dicabut pikeun gampang dibersihkeun

2. Émbaran Kasalametan

Please read all safety instructions before operating the appliance to prevent injury or damage.

• Always place the dispenser on a stable, level surface to prevent tipping.
• Do not fill the dispenser with hot liquids. This dispenser is designed for cold beverages only.
• Exercise caution when handling the dispenser, especially when full, due to its weight.
• Jauhkeun tina jangkauan barudak.
• Do not use abrasive cleaners or scouring pads, as they can scratch the stainless steel or polycarbonate surfaces.
• Produk ieu teu aman dishwasher. Ngumbah leungeun sakabeh komponen.

3. Daptar Bagian

Before assembly, ensure all parts are present and undamaged:

1. Dasar Stainless Steel
2. Removable Netes Baki
3. Clear Polycarbonate Juice Container (2.2 Gallon capacity)
4. Tutup Stainless Steel
5. Stainless Steel Ice Chamber (removable)
6. Spigot/Faucet Assembly

Gambar 1: Winco Stainless Steel Juice Dispenser, Model 902. Shows the complete assembled unit including the base, clear container, lid, and spigot.

4. Setup jeung Majelis

Follow these steps to assemble your juice dispenser:

1. Ngabongkar: Cabut sadaya komponén tina bungkusna kalayan ati-ati. Simpen bungkusna kanggo disimpen engké upami diperyogikeun.
2. Bersih: Before first use, wash all parts that will come into contact with beverages (juice container, lid, ice chamber, spigot) with warm, soapy water. Rinse thoroughly and dry completely.
3. Assemble Spigot: Ensure the spigot is securely attached to the juice container. If it requires assembly, follow the instructions provided with the spigot. Ensure all washers and nuts are tightened to prevent leaks.
4. Tempatkeun Baki Tetes: Position the removable drip tray onto the stainless steel base.
5. Position Juice Container: Carefully place the clean polycarbonate juice container onto the stainless steel base, ensuring it sits securely above the drip tray.
6. Insert Ice Chamber: If using, fill the stainless steel ice chamber with ice cubes and insert it into the center of the juice container.
7. Add Beverage: Pour your desired cold beverage into the polycarbonate container. Do not overfill.
8. Tutup Tempat: Securely place the stainless steel lid on top of the juice container.

5. Parentah Operasi

Using your Winco Juice Dispenser is straightforward:

1. Ensure the dispenser is fully assembled and filled with your cold beverage.
2. To dispense, push the spigot lever down. The beverage will flow out.
3. To stop dispensing, release the spigot lever.
4. Monitor the ice chamber and refill with ice as needed to maintain beverage temperature.
5. Regularly check the drip tray and empty it when full to prevent overflow.

6. Pangropéa jeung beberesih

Proper cleaning and maintenance will extend the life of your dispenser.

beberesih poean:

1. kosong: After each use, empty any remaining beverage from the container.
2. ngabongkar: Remove the lid, ice chamber, and juice container from the base. Detach the spigot from the container. Empty the drip tray.
3. nyeuseuh: Hand wash all components (juice container, lid, ice chamber, spigot, drip tray) with warm water and a mild, non-abrasive dish soap. Use a soft cloth or sponge. For the spigot, ensure thorough cleaning to prevent residue buildup.
4. Bilas: Bilas sadaya bagian sacara saksama nganggo cai bersih pikeun miceun sadaya sésa sabun.
5. garing: Dry all components completely with a soft, clean cloth to prevent water spots and rust on stainless steel parts. Allow the polycarbonate container to air dry fully before reassembly or storage.
6. Dasar bersih: Wipe down the stainless steel base with a damp lawon sarta garing geuwat.

Panyimpenan:

Store the disassembled, clean, and dry dispenser in a cool, dry place. Avoid stacking heavy items on the polycarbonate container to prevent damage.

7. Cara ngungkulan

Ieu mangrupikeun solusi pikeun masalah umum anu anjeun tingali:

• Leakage from Spigot:
  Solusi: Ensure the spigot is properly installed and tightened. Check that all rubber washers are correctly seated and not damaged. If the spigot is old or damaged, it may need replacement.
• Slow Dispensing:
  Solusi: Check if the beverage contains pulp or fruit pieces that might be clogging the spigot. Clean the spigot thoroughly. Ensure the ice chamber is not obstructing the flow.
• Beverage Not Staying Cold:
  Solusi: Ensure the ice chamber is filled with sufficient ice. Replace melted ice regularly. The dispenser is designed for temporary chilling, not long-term refrigeration.
• Cloudy Polycarbonate Container:
  Solusi: This can occur from using abrasive cleaners or hard water. Use only mild soap and soft cloths for cleaning. For hard water stains, a solution of white vinegar and water can help, followed by thorough rinsing.

8. Spésifikasi

9. Garansi jeung Rojongan

For warranty information or technical support regarding your Winco Stainless Steel Juice Dispenser, Model 902, please refer to the documentation included with your purchase or contact Winco customer service directly. Contact details can typically be found on the manufacturer's official websitus atanapi dina resi pameseran Anjeun.