Bubuka
This user manual provides comprehensive instructions for the KERBL Fence Check with LED Display, Model 44669. It covers product overview, setup, operation, maintenance, and troubleshooting. Please read this manual thoroughly before using the device to ensure safe and effective operation.
The KERBL Fence Check is designed for convenient, non-contact measurement of electric fence voltage. It features an LED display for clear voltage indication and a battery status indicator.
Émbaran Kasalametan
- Always handle electrical testing equipment with care.
- Ulah nyobian muka atawa ngaropéa alat. Henteu aya bagian anu tiasa dilayanan ku pangguna di jero.
- Keep the device dry. Exposure to moisture can damage the electronics and pose a safety risk.
- Nyimpen alat jauh tina jangkauan barudak.
- Ensure the battery is correctly installed before use.
- This device is for testing electric fence voltage only. Do not use it for other purposes.
Produk Leuwihview
The KERBL Fence Check is a compact, handheld device designed for quick and easy electric fence voltage testing. It operates wirelessly, eliminating the need for a ground spike.
Gambar 1: Hareupeun view of the KERBL Fence Check device, highlighting the LED voltage indicators, low kV warning, battery status light, and the 'PUSH' button.
komponén:
- Voltage Indicator LEDs: Four green LEDs indicating voltage levels (2.5 kV, 4.0 kV, 6.0 kV, 8.0 kV).
- Low kV LED: A red LED indicating low voltage.
- LED Status Batré: An LED indicating the battery charge level.
- Tombol PUSH: Ngaktipkeun fungsi pangukuran.
- Kompartemen batré: Located on the back (not visible in Figure 1).
Disetél
Pamasangan batré:
- Teang tempat panutup kompartemen batre dina tonggong alat.
- Carefully slide or unclip the cover to open it.
- Insert one 9-volt block battery, ensuring correct polarity (+ and -). The device comes with a 9-volt block battery included.
- Ganti panutup kompartemen batré aman.
- After battery installation, the battery status LED should briefly illuminate, indicating sufficient power. If it does not, check battery orientation or replace the battery.
Parentah Operasi
The KERBL Fence Check allows for quick and easy voltage measurement without direct contact or a ground spike.
Ngalakukeun pangukuran:
- Tahan alat pageuh dina leungeun anjeun.
- Approach the electric fence wire or tape. The measurement is carried out at a distance of maximum 0 - 5 cm from the fence.
- Press and hold the 'PUSH' button on the front of the device.
- Observe the LED indicators. The voltage is displayed by four bright green diodes in four levels: 2500 volts, 4000 volts, 6000 volts, and 8000 volts.
- Lamun voltage is low, a red LED will illuminate, indicating a potential issue with the fence's power.
- Release the 'PUSH' button once the reading is taken.
Figure 2: A hand pressing the 'PUSH' button to activate the measurement.
Figure 3: Proper usage of the device, held close to the electric fence for measurement.
Ngartos tampilan:
- Green LEDs (2.5 kV, 4.0 kV, 6.0 kV, 8.0 kV): Each illuminated green LED indicates that the fence voltage has reached or exceeded that specific level. For example, if the 6.0 kV LED is lit, the voltage is at least 6000 volts.
- Red LED (Low kV): If this LED illuminates, the fence voltage is below the optimal operating range, indicating a need for inspection or repair of the fence system.
- LED Status Batré: This LED indicates the remaining battery life. If it flashes or remains off during operation, the battery may need replacement.
Figure 4: The diagram on the left shows an incorrect method of testing with a ground spike, while the diagram on the right illustrates the correct non-contact method without a ground spike, as intended for this device.
Pangropéa
- beberesih: Ngusap alat ku kaén anu lemes sareng garing. Ulah make cleaners abrasive atawa pangleyur.
- Ngagantian batré: Replace the 9-volt battery when the battery status LED indicates low power or when the device fails to power on. Refer to the "Battery Installation" section for instructions.
- Panyimpenan: Simpen alat ieu di tempat anu tiis sareng garing, jauh tina sinar panonpoé langsung sareng suhu anu ekstrim. Upami disimpen kanggo waktos anu lami, cabut batréna pikeun nyegah bocor.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Alat teu hurung. | Batré pareum atawa salah dipasang. | Check battery polarity; replace battery. |
| No LED indication when testing. | Device too far from fence; fence has no voltage; battery low. | Ensure device is within 0-5 cm of fence; check fence energizer; replace battery. |
| Only "Low kV" red LED illuminates. | Pager voltage handap teuing. | Inspect fence energizer, connections, and fence line for faults or shorts. |
| Battery status LED indicates low power. | Batré béak. | Replace the 9-volt battery. |
spésifikasi
- Jumlah modél: 44669
- merek: KERBL
- Voltage tampilan: 4 levels (2.5 kV, 4.0 kV, 6.0 kV, 8.0 kV) via green LEDs
- Low Voltage Indikator: LED beureum
- Jarak pangukuran: Max. 0 - 5 cm from fence
- Sumber Daya: 1 x 9-volt block battery (included)
- ukuran: Kira-kira 6.85 x 3.19 x 1.14 inci
- beurat: Kira-kira 3.53 ons
- Pabrikan: Kerbl
Garansi sareng Rojongan
KERBL products are manufactured to high-quality standards. For information regarding warranty coverage and terms, please refer to the warranty card included with your product or visit the official KERBL websitus. Simpen resi pameseran anjeun salaku bukti pameseran.
For technical support or inquiries not covered in this manual, please contact KERBL customer service through their official channels. Contact details can typically be found on the product packaging or the manufacturer's websitus.
