Intermatic ET9250 ET90000 Series 4-Circuit Relay Module Instruction Manual

Bubuka

The Intermatic ET9250 is a 4-circuit relay module designed for use with the Intermatic ET90000 series controllers. This module serves as a replacement part or an upgrade component, allowing for the expansion of the controller's circuit capacity. Each ET9250 module includes four SPDT (Single Pole Double Throw) 30 amp relays, facilitating robust control over various electrical loads.

Émbaran Kasalametan penting

Please read and understand all instructions before installing or operating this device. Failure to follow these instructions could result in property damage, personal injury, or death.

Pegatkeun Daya: Always disconnect power at the circuit breaker or fuse box before installing or servicing this module.
Personil anu mumpuni: Installation and servicing should only be performed by qualified electrical personnel.
Kodeu Lokal: Sadaya kabel kedah saluyu sareng kode listrik nasional sareng lokal.
Pamakéan ditangtoskeun: Do not use this module for purposes other than those specified in this manual.
Kaayaan Lingkungan: Ensure the module is installed in an environment free from excessive moisture, dust, and extreme temperatures.

Produk Leuwihview

The ET9250 module is a compact circuit board designed to integrate seamlessly with compatible Intermatic ET90000 series controllers. It provides additional switching capabilities for your system.

Intermatic ET9250 4-Circuit Relay Module, showing the green circuit board with four black relays, terminal blocks, and a multi-colored wire harness. — **Gambar 1:** Intermatic ET9250 4-Circuit Relay Module. This image displays the Intermatic ET9250 4-Circuit Relay Module. The module features a green circuit board with four black SPDT 30 amp relays (labeled K1, K2, K3, K4). Below the relays are green terminal blocks labeled 'NC' (Normally Closed), 'NO' (Normally Open), and 'COM' (Common) for each of the four circuits. A multi-colored wire harness with a connector is attached to the top left of the board, indicating connection points for the main controller.

Komponén konci kalebet:

Four SPDT 30 Amp Relay: These relays (K1-K4) are the primary switching components, capable of handling loads up to 30 amps.
Blok Terminal: Screw terminals for connecting external loads, clearly marked NC, NO, and COM for each circuit.
Kawat Abah: A multi-colored wire harness for connecting the module to the main ET90000 series controller.

Instalasi jeung Setup

The ET9250 relay module is designed for integration with specific Intermatic ET90000 series controllers, including models such as ET90415CR, ET98015CR, ET91215CR, and ET91615CR. It comes in 4-circuit packs, allowing for system expansion up to a maximum of 16 circuits.

Léngkah-léngkah pamasangan:

Pegatkeun daya: Ensure all power to the ET90000 series controller is disconnected at the main circuit breaker before beginning installation.
Pangontrol Aksés: Open the ET90000 series controller enclosure to access the internal components.
Penempatan modul: Carefully align the ET9250 module with the designated expansion slot or mounting points within the controller.
Connect Wire Harness: Connect the multi-colored wire harness from the ET9250 module to the corresponding connector on the main controller board. Ensure a secure and correct connection.
Modul Aman: Secure the module in place using any provided fasteners or clips.
Wiring Loads: Connect the electrical loads to the NC, NO, and COM terminals on the ET9250 module as required by your application. Refer to the specific wiring diagram for your ET90000 series controller for detailed instructions.
Tutup Kandang: Once all connections are made and verified, close the controller enclosure.
Mulangkeun Daya: Restore power to the controller at the main circuit breaker.
Konfigurasi Sistem: Follow the instructions in your ET90000 series controller manual to configure the newly added circuits.

Operasi

The ET9250 relay module operates under the control of the main ET90000 series controller. Each of the four SPDT 30 amp relays can be programmed and controlled independently by the timer or automation functions of the primary unit. When the controller sends a signal, the corresponding relay will switch, opening or closing the circuit to which it is connected. This allows for automated control of various electrical devices or systems.

Pangropéa

The Intermatic ET9250 relay module is designed for reliable, long-term operation with minimal maintenance. However, periodic inspection can help ensure continued performance.

Inspeksi Visual: Annually inspect the module and its connections for any signs of damage, corrosion, or loose wiring.
Kabersihan: Keep the controller enclosure clean and free of dust and debris, which can impede proper operation and heat dissipation.
Perlindungan Lingkungan: Ensure the module remains protected from moisture and extreme temperatures as per its operating specifications.
Pegatkeun daya: Salawasna pegatkeun listrik sateuacan ngalaksanakeun pamariksaan atanapi beberesih.

Pamérésan masalah

If you experience issues with your ET9250 relay module, consider the following troubleshooting steps:

Teu Aya Daya pikeun Ngamuat: Verify that the main controller is receiving power and is programmed correctly. Check the wiring connections to the ET9250 module and the load for looseness or damage.
Incorrect Switching: Ensure the programming in the main ET90000 series controller is correct for the desired switching action. Check for any error codes or indicators on the main controller.
Modul Teu Dipikawanoh: If the main controller does not recognize the newly installed module, ensure the wire harness is securely connected and that the module is properly seated. Refer to the main controller's manual for module detection procedures.
Overload: If a relay is not switching or appears damaged, check the connected load to ensure it does not exceed the 30 amp rating of the relay.
Bantuan profésional: For persistent issues or if you are unsure about any troubleshooting steps, contact a qualified electrician or Intermatic customer support.

Spésifikasi teknis

Spésifikasi	Rincian
Nomer modél	ET9250
merek	Intermatik
Tipe Kontak	SPDT (Lemparan Ganda Tiang Tunggal)
Peunteun ayeuna	30 Amps
Maksimum Ngalihkeun Ayeuna	30 Amps
Jumlah Sirkuit	4
Tipe Pamasangan	Surface Mount (within controller)
Modeu Operasi	Automatic (controlled by main unit)
Dimensi produk	5 x 3.75 x 1.25 inci
Item Beurat	4.8 ons
UPC	078275127746

Émbaran jaminan

For detailed warranty information regarding the Intermatic ET9250 4-Circuit Relay Module, please refer to the manufacturer's official warranty description provided with your product or visit the Intermatic websitus. Sarat jeung kaayaan jaminan bisa rupa-rupa.

Rojongan Palanggan

If you require further assistance, have questions about installation, operation, or troubleshooting that are not covered in this manual, please contact Intermatic customer support. You can typically find contact information on the Intermatic website or within the documentation provided with your ET90000 series controller.

	Intermatic ET90000 Series Electronic Timer: Installation and Programming Guide Comprehensive guide for installing and programming the Intermatic ET90000 Series Electronic Timer. This 365-day astronomic timer automates lighting, HVAC, and other applications. Learn about setup, wiring, event scheduling, advanced options, and system configuration.
	Pituduh Pamasangan sareng Setelan Saklar Waktu 24 Jam 4-Sirkuit Éléktronik Seri Intermatic ET2145 Comprehensive installation and setup instructions for the Intermatic ET2145C, ET2145CR, and ET2145CP Electronic 4-Circuit 24-Hour Time Switches. Learn how to configure output settings, set date and time, program schedules, manage holidays, and utilize USB data transfer.
	Pituduh Pamasangan sareng Pamrograman Saklar Timer Lampu Intermatic EJ341C/EJ343C Pitunjuk lengkep pikeun masang sareng ngaprogram saklar timer lampu Intermatic EJ341C (Kutub Tunggal) sareng EJ343C (Tilu Arah). Ngawengku setelan, kontrol, metode pemrograman, ngungkulan masalah, sareng spésifikasi.
	Intermatic EI200 Éléktronik In-Wall Countdown Timer - Instalasi jeung Operasi Guide Pituduh lengkep pikeun Intermatic EI200 Electronic In-Wall Countdown Timer. Nyertakeun fitur, rating, léngkah pamasangan, modeu operasi (Mode Timer, Mode Tahan), sareng garansi kawates 1 taun. Ngawengku diagram wiring sareng peringatan kaamanan.
	Pituduh Pamasangan sareng Operasi Timer Hitung Mundur Éléktronik Intermatic EI200 Detailed guide for installing and operating the Intermatic EI200 electronic in-wall countdown timer. Features include 5-30 minute time ranges, continuous HOLD mode, and ratings for 15A general purpose, 1000W tungsten, and 1/4 HP motors. Includes warranty information.
	Timer Pareum Otomatis Éléktronik Intermatic EI40C/E140AC Learn about the Intermatic EI40C/E140AC Electronic Automatic Shut-Off Timer. This guide covers installation, features like programmable timing and warning signals, and troubleshooting for efficient load control in residential and commercial applications.