Buku Panduan Pangguna HP 1810-24G v2 Gigabit SFP Switch anu Tiasa Dipasang dina Rak (J9803A)

1. Bubuka

This manual provides detailed instructions for the installation, configuration, and operation of the HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch (Model J9803A). The HP 1810 Switch Series offers smart-managed, fixed-configuration Gigabit Layer 2 switching capabilities, designed for small business environments requiring an easy-to-administer networking solution.

Please read this manual thoroughly before attempting to install or operate the device. Retain this manual for future reference.

2. Eusi Paket

Carefully unpack the box and verify that all items are present and in good condition. If any item is missing or damaged, contact your vendor immediately.

• HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch (J9803A)
• Kabel listrik
• Rack-mounting hardware (brackets and screws)
• Dokuméntasi (Pituduh Mimitian Gancang, Inpormasi Kasalametan sareng Peraturan)

Gambar 2.1: The retail packaging for the HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch. This box contains the switch unit and all included accessories.

Gambar 2.2: Contents of the HP 1810-24G v2 Switch package, including the switch unit, power cord, and rack-mounting brackets with screws.

3. Pedaran Fisik

3.1 Panel payun

Gambar 3.1: Hareupeun view of the HP 1810-24G v2 Switch, showing the 24 Gigabit Ethernet ports and 2 SFP ports.

The front panel of the HP 1810-24G v2 Switch features the following components:

• 24 x 10/100/1000Base-T Ports: RJ-45 ports for connecting network devices using Ethernet cables. Each port supports auto-negotiation for speed and duplex mode.
• 2 x Gigabit SFP Ports: Small Form-Factor Pluggable ports for fiber optic connections, allowing for extended network reach or uplink to other network devices.
• Indikator LED: Status LEDs for power, system activity, and individual port status (link/activity, speed).
• Tombol Reset: Used to reset the switch to factory default settings.

3.2 Panel tukang

The rear panel typically includes the power input connector and possibly grounding points.

• Inlet Daya AC: Panyambung pikeun kabel kakuatan.

4. Setup jeung Instalasi

4.1 Pancegahan Kasalametan

• Ensure the power source matches the switch's voltage syarat.
• Entong meungpeung lawang angin.
• Avoid placing the switch in direct sunlight or near heat sources.
• Keep the switch away from water or damp lingkungan.

4.2 Pilihan pamasangan

The HP 1810-24G v2 Switch supports both rack-mounting and wall-mounting.

4.2.1 Rak Pamasangan

1. Attach the provided rack-mounting brackets to the sides of the switch using the included screws.
2. Secure the switch into a standard 19-inch equipment rack using appropriate rack screws (not always included).

4.2.2 Pamasangan témbok

1. Identify a suitable wall location, ensuring adequate ventilation and access to power.
2. Use appropriate wall anchors and screws (not included) to secure the switch to the wall.

4.3 Nyambungkeun Daya

1. Sambungkeun hiji tungtung kabel daya kana saluran masuk daya AC dina panel tukang saklar.
2. Sambungkeun tungtung nu sejen tina kabel kakuatan ka outlet listrik grounded.
3. Pastikeun yén LED kakuatan dina panel hareup hurung, nunjukkeun yén switch narima kakuatan.

4.4 Sambungan Jaringan

1. Connect your network devices (computers, servers, access points, etc.) to the RJ-45 Gigabit Ethernet ports using standard Ethernet cables.
2. For fiber optic connections, insert compatible SFP transceivers (not included) into the SFP ports, then connect fiber optic cables.
3. Observe the port LEDs to confirm link status and activity.

5. Parentah Operasi

5.1 Konfigurasi Awal (Web Panganteur)

The HP 1810-24G v2 Switch is a smart-managed switch, configurable via a web-panganteur dumasar.

1. Connect a computer directly to any RJ-45 port on the switch using an Ethernet cable.
2. Configure your computer's IP address to be in the same subnet as the switch's default IP address (refer to the Quick Start Guide for default IP).
3. Buka a web panyungsi wéb teras lebetkeun alamat IP standar saklar.
4. Log in using the default username and password (refer to the Quick Start Guide).
5. Follow the on-screen prompts to change the default password and configure basic network settings, such as the switch's IP address, subnet mask, and gateway.
6. Ngajalajah éta web interface for advanced features like VLAN tagging, Link Aggregation (LACP), Spanning Tree Protocol (STP), Quality of Service (QoS), and SNMP.

5.2 Operasi Jaringan Dasar

Once configured, the switch operates automatically to forward network traffic between connected devices.

• Nyolok sareng Puter: Connect Ethernet devices to any available port. The switch will automatically detect the connection speed and duplex mode.
• Kinerja Gigabit: Supports Gigabit Ethernet speeds (1000 Mbps) for high-bandwidth applications.
• SFP Connectivity: Utilize SFP ports for fiber uplinks to connect to other switches or network segments over longer distances.

6. Pangropéa

6.1 Apdet firmware

Periodically check the Hewlett Packard Enterprise (HPE) support websitus pikeun apdet firmware. Ngajaga firmware tetep mutahir mastikeun kinerja, kaamanan, sareng aksés kana fitur-fitur anyar anu optimal.

1. Download the latest firmware from the official HPE support portal.
2. Aksés saklar web panganteur.
3. Navigate to the firmware upgrade section and follow the instructions to upload and install the new firmware.
4. Catetan: Do not power off the switch during a firmware upgrade.

6.2 beberesih

To maintain proper ventilation and prevent overheating, keep the switch clean.

• Use a soft, dry cloth to wipe the exterior of the switch.
• Use compressed air to clear dust from ventilation openings.
• Entong nganggo pembersih cair atanapi aerosol.

6.3 Ngareset ka Setelan Standar Pabrik

If necessary, the switch can be reset to its factory default settings. This will erase all custom configurations.

1. With the switch powered on, locate the reset button on the front panel.
2. Paké klip kertas atawa objék nunjuk sarupa pikeun mencet jeung tahan tombol reset salila kurang leuwih 10 detik.
3. Release the button when the system LEDs indicate a reset (refer to the Quick Start Guide for specific LED behavior).
4. The switch will reboot with factory default settings.

7. Cara ngungkulan

Bagian ieu nyayogikeun solusi pikeun masalah umum anu anjeun tiasa patepang.

7.1 Taya Daya

• Pastikeun kabel listrik disambungkeun sacara aman ka saklar sareng stop kontak listrik anu tiasa dianggo.
• Pastikeun stop kontak listrik berpungsi ku cara nyolokkeun alat sejen.
• Check the power LED on the front panel. If it is off, contact support.

7.2 Teu Aya Konéktivitas Jaringan

• Check the Ethernet cables for secure connections at both ends.
• Verify the link/activity LED for the connected port. If it is off, try a different port or cable.
• Pastikeun alat anu nyambung parantos dihurungkeun sareng dikonfigurasi kalayan leres.
• If using SFP ports, ensure compatible transceivers are used and fiber cables are correctly connected.
• Confirm the switch's IP address and network settings are correct via the web panganteur.

7.3 Teu Bisa Aksés Web Panganteur

• Ensure your computer's IP address is in the same subnet as the switch.
• Verify you are using the correct IP address for the switch.
• Pupus cache panyungsi anjeun atanapi cobian browser anu sanés.
• If the password was changed and forgotten, you may need to perform a factory reset (see Section 6.3).

8. Spésifikasi

9. Garansi jeung Rojongan

For warranty information and technical support, please refer to the official Hewlett Packard Enterprise (HPE) websitus atanapi dokuméntasi anu kalebet sareng produk anjeun.

Important Notice Regarding Returns and Warranty: Please be aware that returns for non-defective items may not be accepted. Merchandise returned for repair and found not to be defective by technicians may incur a restocking fee. Additional warranty length options may be available; contact your vendor directly for more details.

Kanggo bantosan salajengna, mangga sumping ka kantor resmi Dukungan HPE Websitus.