Einhell TC-MS 2112 T Miter and Table Saw

1. Bubuka

This manual provides essential information for the safe and effective operation, setup, and maintenance of your Einhell TC-MS 2112 T Miter and Table Saw. Please read all instructions carefully before using the tool to ensure personal safety and optimal performance. Keep this manual in a safe place for future reference.

2. Parentah Kasalametan

Peringatan Kasalametan Alat Daya Umum:

• Salawasna nganggo alat pelindung diri anu merenah, kalebet kacamata pengaman, pelindung dédéngéan, sareng masker lebu.
• Pastikeun wewengkon gawé beresih, cahayana alus, sarta bebas tina halangan.
• Jauhkeun barudak sareng jalma anu aya di tempat operasi.
• Ulah ngajalankeun parabot kakuatan dina atmosfir ngabeledug, kayaning ku ayana cair kaduruk, gas, atawa lebu.
• Avoid accidental starting. Ensure the switch is in the off-position before connecting to power, picking up, or carrying the tool.
• Ngajaga footing ditangtoskeun jeung kasaimbangan sepanjang waktos.
• Pegatkeun sambungan colokan ti sumber listrik samemeh nyieun sagala panyesuaian, ngaganti asesoris, atawa nyimpen parabot kakuatan.

Specific Miter and Table Saw Safety Warnings:

• Always use the push stick when operating in table saw mode, especially for narrow workpieces.
• Ensure the blade guard is in place and functioning correctly before each use.
• Never reach into the blade area while the saw is running or connected to power.
• Secure the workpiece firmly before cutting. Do not attempt to hand-hold small pieces.
• Use only sharp, correctly sized saw blades suitable for the material being cut.
• Ngidinan sabeulah pikeun ngahontal speed pinuh saméméh dimimitian cut a.
• Never remove cut-off pieces or other parts of the workpiece from the cutting area while the blade is running.

3. Produk Langkungview

The Einhell TC-MS 2112 T is a versatile 2-in-1 tool, functioning as both a miter saw and a table saw, designed for precise cutting of wood and similar materials.

Gambar 3.1: Gemblengna view of the Einhell TC-MS 2112 T Miter and Table Saw.

Figure 3.2: Close-up of the miter scale and model designation on the saw base.

Gambar 3.3: View of the integrated table extension for supporting longer workpieces.

Figure 3.4: The parallel guide, used for consistent rip cuts in table saw mode.

4. Setup jeung Majelis

Sateuacan dianggo mimiti, pastikeun sadaya komponén aya sareng henteu ruksak. Tingali daptar bungkus kanggo verifikasi.

1. Ngabongkar bungkusan: Carefully remove the saw and all accessories from the packaging. Retain packaging for potential future transport or storage.
2. Stabilitas dasar: Place the saw on a stable, level workbench. Secure the saw to the workbench using appropriate fasteners through the mounting holes in the base to prevent movement during operation.
3. Pemasangan Bilah (upami teu acan dipasang sateuacanna): Ensure the saw is unplugged. Follow the instructions for safely installing the 210mm saw blade, ensuring the rotation direction matches the arrow on the saw.
4. Pariksa penjaga: Verify that all blade guards move freely and return to their protective positions automatically.
5. Éksténsi Méja: Extend the workpiece supports (extensions) as needed for longer materials.

5. Parentah Operasi

The Einhell TC-MS 2112 T offers both miter saw and table saw functionalities. Always select the appropriate mode for your cutting task.

5.1. Miter Saw Function

For cross-cutting and angle cuts on workpieces.

1. Nyaluyukeun Sudut Mitre: Loosen the locking knob for the turntable. Rotate the turntable to the desired angle (up to 45° left or right). Securely tighten the locking knob.
2. Nyaluyukeun Sudut Bevel: Loosen the locking mechanism for the saw head. Tilt the saw head to the desired bevel angle (up to 45° to the left). Securely tighten the locking mechanism.
3. Positioning Workpiece: Place the workpiece firmly against the fence and the turntable. Use clamps lamun perlu.
4. Nyieun Motong: Depress the safety switch and then the main power switch. Allow the blade to reach full speed. Slowly lower the saw head through the workpiece. Once the cut is complete, release the power switch and allow the blade to stop before raising the saw head.

Figure 5.1: Demonstrating the miter saw function for angled cuts.

Figure 5.2: Illustration of a 90° x 90° cross-cut (max. 120 x 55 mm).

Figure 5.3: Illustration of a 90° x 45° miter cut (max. 65 x 55 mm).

Figure 5.4: Illustration of a 45° x 45° compound miter cut (max. 40 x 23 mm).

5.2. Table Saw Function

For ripping and sizing workpieces.

1. Converting to Table Saw: Ensure the saw head is locked in the upright position. Adjust the blade height using the appropriate mechanism.
2. Adjusting Blade Height: Use the height adjustment knob to set the desired blade exposure above the table (0-33 mm).
3. Using Parallel Guide: Position the parallel guide to achieve the desired cutting width. Securely lock the guide in place.
4. Positioning Workpiece: Place the workpiece on the table, ensuring it is flat and against the parallel guide.
5. Nyieun Motong: Depress the safety switch and then the main power switch. Allow the blade to reach full speed. Using the push stick, slowly feed the workpiece through the blade. Never use your hands to push the workpiece directly into the blade.

Figure 5.5: Demonstrating the table saw function for rip cuts.

Figure 5.6: Close-up of the blade height adjustment for table saw mode.

Figure 5.7: The included push stick, essential for safe table saw operation.

5.3. Pangeluaran Lebu

The saw is equipped with a dust extraction port to connect to a vacuum cleaner or dust extractor, helping to keep the work area clean and reduce airborne dust.

Figure 5.8: The dust extraction port for connecting a vacuum system.

6. Pangropéa

Pangropéa rutin ngajamin umur panjang sareng operasi anu aman tina ragaji anjeun.

• beberesih: After each use, disconnect the saw from power and clean off dust and debris using a brush or compressed air. Do not use harsh chemicals.
• Gantian sabeulah: When the saw blade becomes dull or damaged, replace it with a new, sharp blade of the correct size (210mm diameter, 30mm bore). Always unplug the saw and use appropriate tools for safe blade removal and installation.
• Lubrication: Periodically apply a light machine oil to moving parts and pivot points to ensure smooth operation.
• Pamariksaan: Regularly inspect the power cord, plug, switches, and guards for any signs of damage or wear. Replace damaged parts immediately.
• Panyimpenan: Simpen gergaji di tempat anu garing, aman, sareng teu kahontal ku barudak.

7. Cara ngungkulan

Bagian ieu ngabahas masalah umum anu anjeun tingali.

8. Spésifikasi

Technical data for the Einhell TC-MS 2112 T Miter and Table Saw.

Figure 8.1: Blade specifications.

Figure 8.2: Max cut depth.

Figure 8.3: Height adjustment range.

Figure 8.4: Product weight.

9. Garansi

This Einhell product is covered by a manufacturer's warranty. Please refer to the warranty card included with your purchase or visit the official Einhell websitus pikeun istilah jeung kaayaan lengkep ngeunaan sinyalna jaminan na klaim.

10. Rojongan Palanggan

For technical assistance, spare parts, or further information, please contact Einhell customer service or visit their official websitus:

• Websitus: www.einhell.com
• Inpormasi kontak: Tingal bagian kontak dina resmi websitus pikeun detil rojongan régional.