GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Bubuka

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Émbaran Kasalametan

PERHATOSAN: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Alat ieu dimaksudkeun pikeun pamasangan saluyu sareng Kode Listrik Nasional sareng peraturan lokal.
• Do not use in wet locations or where directly exposed to water.
• Pikeun pamakéan indoor wungkul.

Eusi pakét

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Screws pamasangan
• Wire Nuts (may vary by package)
• Manual pangguna (dokumén ieu)

Setup sareng Instalasi

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Pareuman Daya: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Hapus Switch Old: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Identipikasi Kawat:
   • Jalur (Panas): Usually black, coming from the circuit breaker.
   • Beban: Usually black, going to the light fixture or appliance.
   • nétral: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • taneuh: Usually green or bare copper.
4. Sambungkeun Saklar Anyar: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Nyambungkeun Jalur wire to the terminal marked "LINE".
   • Nyambungkeun ngamuat wire to the terminal marked "LOAD".
   • Nyambungkeun nétral wire to the terminal marked "NEUTRAL".
   • Nyambungkeun taneuh wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Saklar Gunung: Taliti nyorong switch kabel kana kotak témbok. Ngamankeun eta kalawan screws disadiakeun.
6. Pasang Plat Tembok: Tempelkeun pelat témbok anyar atanapi anu tos aya.
7. Mulangkeun Daya: Hurungkeun kakuatan deui ON di circuit breaker.

Gambar 1: Hareupeun view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle sakali. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Ngoperasikeun Switch

Kontrol Manual

• Pencét éta luhur of the paddle to turn the connected load ON.
• Pencét éta handap of the paddle to turn the connected load Pareum.

Kontrol Gelombang Z

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Pangropéa

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• beberesih: Pikeun ngabersihkeun saklar, usap ku kaén anu lemes,amp lawon. Ulah make cleaners abrasive atawa pangleyur.
• Pembaruan firmware: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Perawatan Umum: Pastikeun saklar henteu kakeunaan kalembaban anu kaleuleuwihi atanapi suhu anu ekstrim.

Pamérésan masalah

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle sakali. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

spésifikasi

Garansi sareng Rojongan

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl websitus atanapi ngahubungan departemén layanan palanggan maranéhna.

Websitus: www.gocontrol.com

Pabrikan: GOCONTROL