1. Bubuka
This manual provides essential instructions for the safe and effective use, setup, operation, and maintenance of your Edwards Manufacturing 21mm Metric Punch & Die Set, model PDM21. Please read this manual thoroughly before using the product to ensure proper function and to prevent injury or damage.
2. Produk Langkungview
The Edwards PDM21 is a standard metric round punch and die set designed for creating 21mm holes in various materials. It consists of two primary components: the punch and the die. This set is engineered to fit into a standard punch holder (not included).
Gambar 1: The Edwards 21mm Metric Punch and Die Set. The image displays two metal components: a punch (left) with a pointed tip and a cylindrical body, and a die (right) which is a thicker, flat cylinder with a central hole. The punch is marked "21MM" and the die is marked "21.8MM".
komponén:
- Pukulan: A 21mm diameter component designed to cut through material. It features a pointed tip for accurate centering.
- Die: A 21.8mm diameter component that supports the material and allows the punch to pass through, ensuring a clean cut.
3. Setélan
Proper setup is crucial for safe operation and optimal performance. Always ensure the power to the punch machine is disconnected before installing or removing tooling.
- Kasalametan munggaran: Wear appropriate personal protective equipment (PPE), including safety glasses and gloves. Ensure the punch machine is powered off and locked out according to safety procedures.
- Mariksa komponén: Before installation, inspect both the punch and die for any signs of damage, wear, or debris. Clean if necessary.
- Install Die: Place the 21.8mm die into the appropriate die holder on your punch machine. Ensure it is seated correctly and securely.
- Install Punch: Insert the 21mm punch into the punch ram or punch holder. Secure it firmly according to your machine's instructions.
- Align Punch and Die: Carefully align the punch with the die. The punch should enter the die cleanly without interference. Adjust alignment as needed, following your punch machine's manual.
- Test Fit: Manually cycle the punch machine (if possible and safe) to verify the punch enters the die without binding.
4. Parentah Operasi
Once the punch and die set is correctly installed and aligned, you can proceed with punching operations. Always prioritize safety.
- Nyiapkeun bahan: Ensure the material to be punched is clean, flat, and free of obstructions. Mark the desired punch location accurately.
- Bahan Posisi: Place the material securely on the die, aligning the marked punch location directly over the die's opening.
- Engage Punch: Activate the punch machine according to its operating instructions. The punch will descend, cut through the material, and retract.
- Hapus Bahan: Once the punch has fully retracted, carefully remove the punched material and the slug (the cut-out piece).
- Ulang deui: Continue punching as needed, ensuring proper alignment and material handling for each operation.
Pancegahan Kasalametan:
- Never operate the punch machine without proper guarding in place.
- Keep hands and fingers clear of the punch and die area during operation.
- Do not attempt to punch materials beyond the capacity of your machine or the punch and die set.
- Regularly inspect the punch and die for wear or damage. Replace worn components immediately.
5. Pangropéa
Regular maintenance extends the life of your punch and die set and ensures consistent performance.
- beberesih: After each use, clean the punch and die to remove any material residue, burrs, or debris. A wire brush or compressed air can be used.
- Lubrication: Apply a light coat of machine oil or a suitable lubricant to the punch and die surfaces, especially the cutting edges, to prevent rust and reduce friction.
- Pamariksaan: Periodically inspect for signs of wear, chipping, or dullness on the cutting edges. A dull punch or die can lead to poor cut quality and increased stress on the machine.
- Panyimpenan: Store the punch and die set in a clean, dry environment to prevent corrosion. Consider using a protective case or rack.
6. Cara ngungkulan
Tingali kana bagian ieu pikeun masalah umum sareng solusi poténsialna.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Rough or Burred Edges | Dull punch/die, improper alignment, incorrect material support. | Inspect and sharpen/replace punch/die. Re-align tooling. Ensure material is properly supported. |
| Punch Sticking in Material | Lack of lubrication, excessive material thickness, worn stripper plate (if applicable). | Apply lubricant. Verify material thickness is within capacity. Check and replace stripper plate if worn. |
| Punch Not Centering Accurately | Misalignment of punch and die, worn punch tip. | Re-align punch and die. Inspect punch tip for wear and replace if necessary. |
7. Spésifikasi
Key technical specifications for the Edwards Manufacturing 21mm Metric Punch & Die Set (PDM21).
- merek: Edwards
- Jumlah modél: PDM21
- Punch Diameter: 21 mm
- Die Diameter: 21.8 mm
- Modeu operasi: Manual (requires compatible punch machine)
- Bahan: logam
- Beurat barang: Kira-kira 2 Pon (0.91 kg)
- Ukuran Paket: Kira-kira 9 x 5.75 x 0.38 inci (22.86 x 14.61 x 0.97 cm)
- UPC: 731325582154
- Pabrikan: JPW Industries
8. Garansi jeung Rojongan
Specific warranty terms and detailed support contact information for the Edwards Manufacturing 21mm Metric Punch & Die Set (PDM21) are not provided within the available product data. For warranty claims, technical assistance, or to purchase replacement parts, please refer to the documentation included with your punch machine or contact Edwards Manufacturing directly through their official websitus atanapi distributor otorisasi.
Anjeun oge bisa nganjang ka Edwards Store on Amazon pikeun inpo nu leuwih lengkep.
