1. Produk Langkungview
The Icstation DC 12V Time Delay Switch Module is a programmable digital timer relay designed for various applications requiring precise ON-Off control. It features a dual LED display for clear indication of process value (PV) and set value (SV), along with tactile push-buttons for easy configuration. This module supports multiple working modes, including timing, delay, and cycle operations, with a wide time range from 1 second to 999 hours.
Figure 1: Icstation DC 12V Time Delay Switch Module. This image shows the front view of the module with its dual LED display and control buttons.
2. Émbaran Kasalametan
Mangga baca sareng ngartos sadaya parentah kaamanan sateuacan ngoperasikeun alat ieu. Gagalna nuturkeun parentah ieu bisa ngakibatkeun shock listrik, seuneu, atawa tatu serius.
- Pastikeun catu daya voltage matches the module's specified operating voltage (DC 12V).
- Do not exceed the maximum compatible load of AC 250V 10A / DC 30V 10A.
- Pegatkeun sambungan listrik sateuacan nyieun sambungan atanapi panyesuaian kabel naon waé.
- Avoid exposing the module to moisture, extreme temperatures, or corrosive environments.
- Pamasangan kedah dilakukeun ku tanaga anu mumpuni upami anjeun teu yakin ngeunaan kabel listrik.
3. Eusi Paket
Saatos muka bungkusan, mangga pariksa yén sadaya komponén aya sareng henteu ruksak:
- 1x Icstation DC 12V Time Delay Switch Module
- 1x Digital User Manual (available for download on the product page)
Gambar 2: Internal view of the module, showing the relay and circuit board. This image provides a glimpse into the module's construction.
4. Spésifikasi
Gambar 3: Produk leuwihview with labeled components and a specifications table.
| Fitur | Nilai |
|---|---|
| Gawé Voltage | DC 12V |
| Rentang Timing | 0-999s, 0-999m, 0-999h |
| Fungsi | Timer, Delay, Cycle |
| Arus maksimum | 10A |
| Compatible Load | AC 250V 10A / DC 30V 10A |
| Ukuran Pamasangan | 71 X 40 X 24mm (2.79 X 1.57 X 0.94 inch) |
| Tipe tampilan | Dual Green-Red LED |
| Item Beurat | 41 Gram (1.45 ons) |
| Bahan | palastik |
5. Setélan
5.1 Diagram Wiring
The module requires a DC 12V power supply. The load is connected to the relay contacts. Ensure correct polarity and secure connections to prevent short circuits or disconnections.
Figure 4: Two common wiring diagrams for the module. This image illustrates how to connect the power supply and the load to the timer relay.
Figure 5: Another detailed wiring diagram showing connections for VCC, GND, S1, and S0 terminals. VCC and GND are for module power, while S1 and S0 are relay contacts for the load.
- VCC: Connect to the positive (+) terminal of your DC 12V power supply.
- GND: Connect to the negative (-) terminal of your DC 12V power supply.
- S1 & S0: These are the relay contacts. Connect your load (e.g., light, water pump, engine) across these two terminals. The relay acts as a switch, opening or closing the circuit to the load based on the programmed timing.
6. Parentah Operasi
6.1 Pidangkeunview
The module features a dual LED display:
- PV (Nilai Prosés): Red display, shows the current countdown or elapsed time.
- SV (Nilai Setél): Green display, shows the programmed time setting.
6.2 Setting Time Parameters
To set the time parameters (T1 for ON time, T2 for OFF time) and the time unit (seconds, minutes, hours):
- Pencét éta SET button once. The PV (red) display will flash, indicating you can set the ON time (T1). Use the UP jeung TURUN tombol pikeun nyaluyukeun nilai.
- Pencét SET again. The SV (green) display will flash, indicating you can set the OFF time (T2). Use the UP jeung TURUN tombol pikeun nyaluyukeun nilai.
- Pencét SET a third time. The PV display will show 'P0', 'P1', or 'P2' (or similar, depending on the specific model's firmware) to select the time unit. Use UP jeung TURUN pikeun siklus ngaliwatan:
- P0: Seconds (0-999s)
- P1: Minutes (0-999m)
- P2: Hours (0-999h)
- Pencét SET again to save the settings and exit.
6.3 Modeu operasi
Pikeun milih modeu operasi:
- Pencét jeung tahan tombol SET button for approximately 3 seconds until the PV display shows 'P1.X' (where X is the mode number).
- Ngagunakeun éta UP jeung TURUN buttons to cycle through the available modes (P1.0 to P1.6, or similar). Each mode defines a different timing behavior:
- P1.0 (Delay ON): After power-on, the relay remains OFF for T1 time, then turns ON indefinitely.
- P1.1 (Delay OFF): After power-on, the relay turns ON for T1 time, then turns OFF indefinitely.
- P1.2 (Cycle ON/OFF): After power-on, the relay turns ON for T1 time, then OFF for T2 time, and repeats this cycle indefinitely.
- P1.3 (Cycle OFF/ON): After power-on, the relay remains OFF for T1 time, then turns ON for T2 time, and repeats this cycle indefinitely.
- P1.4 (Single Delay ON): After power-on, the relay remains OFF for T1 time, then turns ON for T2 time, and then turns OFF indefinitely.
- P1.5 (Single Delay OFF): After power-on, the relay turns ON for T1 time, then turns OFF for T2 time, and then turns ON indefinitely.
- P1.6 (Trigger Delay ON): The relay is triggered by an external signal (not directly supported by this model's basic buttons, typically an external input pin), then turns ON for T1 time, then OFF indefinitely.
- Saatos mode anu dipikahoyong dipilih, pencét tombol SET tombol pikeun nyimpen jeung kaluar.
Figure 6: The module can be used in various applications such as controlling lights, water pumps, or other timed devices.
7. Pangropéa
To ensure the longevity and optimal performance of your Icstation Time Delay Switch Module, follow these maintenance guidelines:
- beberesih: Gently wipe the module with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Panyimpenan: Store the module in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Pamariksaan: Periodically check wiring connections for tightness and signs of wear or corrosion.
8. Cara ngungkulan
If you encounter issues with your module, refer to the following common troubleshooting steps:
- Modul teu hurung:
- Check the DC 12V power supply connection and ensure it is providing the correct voltage.
- Verify VCC and GND connections for correct polarity.
- Beban teu robah:
- Ensure the load is correctly wired to the S1 and S0 relay contacts.
- Check if the programmed timing parameters (T1, T2) and operating mode are set correctly.
- Verify that the load itself is functional and not drawing excessive current beyond the module's rating.
- Incorrect timing or erratic behavior:
- Double-check the time unit setting (seconds, minutes, hours).
- Ensure stable power supply. Fluctuations in voltage can affect performance.
- Reset the module by disconnecting and reconnecting power, then re-enter your desired settings.
9. Garansi jeung Rojongan
Icstation products are designed for reliability and performance. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or further inquiries, please refer to the official Icstation store on Amazon or contact their customer service directly.
Nganjang ka Toko Icstation pikeun inpo nu leuwih lengkep sarta apdet produk.
