1. Produk Langkungview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. Émbaran Kasalametan
Salawasna perhatoskeun tindakan pencegahan kaamanan dasar pikeun ngirangan résiko kahuruan, sengatan listrik, sareng tatu pribadi nalika nganggo produk ieu.
- Baca Manual: Thoroughly read and understand all instructions before operating the spray gun.
- Alat Pelindung Diri (APD): Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- Ventilasi: Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- Bahan anu gampang kaduruk: Do not spray flammable or combustible materials near open flames, pilot lights, or other ignition sources.
- Kasalametan listrik: Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- Jauhkeun Barudak: Do not allow children or untrained persons to operate the spray gun.
- Sambungan Aman: Ensure all air hose connections are secure before operation.
3. Komponén jeung Bagian
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- Hawa Inlet Panyambung
Gambar 2: Sisi view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. Setélan
- Ngabongkar: Sacara saksama miceun sadaya komponén tina bungkusan. Mariksa karusakan naon waé.
- Sambungkeun Kompresor Udara: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- Nyiapkeun Bahan: Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- Pangaluyuan Awal: Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. Parentah Operasi
- Power On Compressor: Turn on your air compressor and allow it to build up sufficient pressure.
- Pola Semprotan Uji: Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- Téhnik nyemprot: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- ngeusian: If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. Pangropéa
Beberesih sareng perawatan anu leres penting pisan pikeun umur panjang sareng kinerja pistol semprot anjeun.
- Geura beberesih: Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- Pembongkaran: Bongkar wadah cet, nozzle, jeung tutup hawa.
- Komponén beberesih: Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- Reassembly: Reassemble the spray gun once all parts are clean and dry.
- Panyimpenan: Simpen pistol semprot di tempat anu bersih sareng garing, jauh tina suhu anu ekstrim sareng sinar panonpoé langsung.
7. Cara ngungkulan
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Taya semprot atawa semprot lemah | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| Pola semprot teu rata | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. Spésifikasi
- Ngaran modél: ASG-SFEU; EX; UK
- Jumlah modél: 4472350
- merek: Ozito
- Ukuran Nozzle: 1.5 mm
- Paint Pot Capacity: 1000 ml
- Minimum Air Compressor Flow Rate: 85 liter per menit
- warna: kulawu
- Komponén Kaasup: 1 suction spray gun
- Ukuran Paket: 28.5 x 19 x 11 cm
- Beurat barang: 790 gram
- Pabrikan: Einhell
9. Garansi jeung Rojongan
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Sumberdaya Online: Nganjang www.ozito.com.au (or your regional Ozito website) for product registration, FAQs, and support contact details.
