SOMMER 4019 Pearl Vibe Garage Remote Control User Manual

Bubuka

This manual provides detailed instructions for the setup, operation, and maintenance of your SOMMER 4019 Pearl Vibe garage remote control. Designed for ease of use, this remote offers reliable control over your garage door system.

Figure 1: SOMMER 4019 Pearl Vibe Remote Control

Fitur konci:

• Ability to check door position or receiver status.
• Tactile feedback (vibration) for command confirmation.
• Efficient vibration motor for extended battery life.
• Interference-resistant radio signal with 128-bit encoding.
• Shock-resistant design for durability.
• Bidirectional radio communication.

Setup jeung Programming

To program your SOMMER 4019 Pearl Vibe remote control, follow these steps. Ensure you have access to your garage door opener's radio receiver.

1. Activate Learning Mode: Press the learning button on your radio receiver. The LED indicator on the receiver will illuminate, indicating it is in learning mode.
2. Program Remote Button: On your new remote control, press the desired button for 1-2 seconds. The receiver's LED will flash, confirming the signal reception.
3. Operasi tés: Press the programmed remote control button again to confirm that the garage door opener responds normally.

For a visual guide on programming, please refer to the following video:

Additional programming demonstrations:

Parentah Operasi

The SOMMER 4019 Pearl Vibe remote control is designed for simple and intuitive operation.

• Bubuka/Penutup: Press the programmed button once to activate your garage door. The door will open or close depending on its current state.
• Stopping Movement: Press the button again while the door is in motion to stop it.
• Eupan Balik Geter: The remote provides a subtle vibration to confirm that your command has been sent.
• Status Check (if supported by receiver): Some advanced receivers allow you to check the door's current position or the receiver's status. Refer to your garage door opener's manual for specific instructions on this feature.

Pangropéa

Pikeun mastikeun kinerja anu optimal sareng umur panjang tina remote control anjeun, turutan pedoman perawatan ieu:

• beberesih: Wipe the remote control with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• Ngagantian batré: The SOMMER 4019 Pearl Vibe uses an alkaline battery. When the remote's indicator light dims or its range decreases, it's time to replace the battery.

Léngkah Ngagantian Batré:

1. Carefully slide open the remote control casing.
2. Remove the old battery, noting its polarity.
3. Insert a new alkaline battery (e.g., CR2032 type, if applicable, though not specified in JSON, common for remotes), ensuring correct polarity.
4. Close the remote control casing aman.

For a visual demonstration of battery replacement, refer to the following video:

• Panyimpenan: Simpen remote di tempat anu garing, jauh tina suhu anu ekstrim sareng sinar panonpoé langsung.

Pamérésan masalah

If you encounter issues with your SOMMER 4019 Pearl Vibe remote control, try the following solutions:

• Jauh Teu Ngabales:
  • Pariksa batréna. Ganti upami diperyogikeun.
  • Pastikeun anjeun aya dina jarak operasi (dugi ka 10 méter).
  • Verify that the remote is correctly programmed to your receiver. If unsure, repeat the programming steps.
• Rentang ngurangan:
  • Ganti batréna.
  • Check for any obstructions between the remote and the receiver (e.g., metal objects, thick walls).
  • Ensure the receiver's antenna is not obstructed or damaged.
• Operasi intermittent:
  • This could indicate a low battery.
  • Check for sources of radio interference in the vicinity (e.g., other wireless devices, power lines).

If problems persist after trying these steps, consult a qualified technician or contact SOMMER customer support.

spésifikasi

Garansi sareng Rojongan

For warranty information, please refer to the documentation provided with your purchase or visit the official SOMMER website. For technical support or further assistance, please contact SOMMER customer service directly.