Bubuka
This manual provides instructions for the proper installation and use of the HPE HP 685183-001 Mini SAS Cable, designed for DL360E servers. Please read this manual carefully before installation to ensure correct setup and operation.
Image: The HPE HP 685183-001 Mini SAS Cable, featuring a black braided exterior and two male Mini SAS connectors at each end. The cable is coiled, illustrating its typical appearance and flexibility.
Émbaran Kasalametan
Always handle electronic components with care. Ensure power is disconnected from the system before installing or removing cables to prevent electrical shock or damage to components. Observe proper electrostatic discharge (ESD) precautions when working inside a server chassis.
Setup sareng Instalasi
Follow these steps to properly install the Mini SAS cable:
- Persiapan: Power down the server and disconnect all power cables. Open the server chassis according to the server's service manual.
- Identipikasi palabuhan: Locate the Mini SAS ports on your server's motherboard or RAID controller and the corresponding ports on your storage backplane or drive cage. These ports are typically labeled for easy identification.
- Sambungkeun kabel: Gently insert one end of the HPE HP 685183-001 Mini SAS cable into the Mini SAS port on the motherboard/controller. Ensure it clicks securely into place, indicating a proper connection.
- Kabel Jalur: Carefully route the cable to avoid obstructing airflow, interfering with other components, or being pinched by chassis parts.
- Sambungkeun tungtung kadua: Connect the other end of the Mini SAS cable to the corresponding port on the storage backplane or drive cage, ensuring a secure connection.
- Secure Chassis: Tutup chassis server tur sambungkeun deui sakabeh kabel kakuatan.
- Daya Hurung: Power on the server and verify that the connected storage devices are recognized by the system's BIOS/UEFI or operating system.
Parentah Operasi
Once installed, the HPE HP 685183-001 Mini SAS cable operates passively, facilitating high-speed data transfer between your server's controller and storage devices. No specific user interaction is required for its operation beyond proper installation.
Pangropéa
The HPE HP 685183-001 Mini SAS cable requires minimal maintenance. Periodically inspect the cable for any signs of physical damage, such as cuts, kinks, or frayed shielding. Ensure connectors remain securely seated. Do not bend the cable sharply or apply excessive force to the connectors, as this can damage internal wiring or the connectors themselves.
Pamérésan masalah
- Alat Panyimpenan Teu Kadeteksi:
- Verify that both ends of the Mini SAS cable are securely connected to their respective ports.
- Ensure the server is powered off before checking connections to prevent damage.
- Check the server's BIOS/UEFI or RAID controller settings to confirm storage device detection and configuration.
- If possible, test with a known working Mini SAS cable to rule out cable failure as the cause.
- Konektipitas Intermittent:
- Ensure the cable is not pinched or bent excessively, which can disrupt signal integrity.
- Check for any loose connections at either end of the cable.
- Inspect the cable and connectors for any visible physical damage.
spésifikasi
| Fitur | Rincian |
|---|---|
| merek | HEWLETT PACKARD (HPE) |
| Nomer modél | 685183-001 |
| Tipe Panyambung | Mini SAS |
| Panyambung Génder | Jalu-ka-Jalu |
| Wangun Kabel | Buleud |
| Jumlah Unit | 1.0 Ngitung |
| ASIN | B085VHKKRF |
| Tanggal Sadia munggaran | 2 April 2020 |
Garansi sareng Rojongan
Specific warranty information for the HPE HP 685183-001 Mini SAS Cable is typically provided at the point of purchase or through the official HPE documentation accompanying your server system. For technical support or warranty claims, please refer to the official Hewlett Packard Enterprise (HPE) support channels or contact your product vendor directly.
