Eogifee UC9050T Universal Ceiling Fan Wall Control

Émbaran Kasalametan penting

Please read and understand all instructions before installing or operating this product. Failure to follow these instructions may result in electric shock, fire, or other hazards which could cause property damage, personal injury, or death.

• Always disconnect power at the circuit breaker or fuse box before installation or servicing.
• This device is intended for use with ceiling fans only.
• Pastikeun sadaya sambungan kabel aman sareng sasuai sareng kode listrik lokal.
• Do not exceed the maximum electrical ratings of the device.
• Taroskeun ka tukang listrik anu mumpuni upami anjeun henteu yakin kana bagian mana waé tina prosés pamasangan.

Eusi pakét

Pariksa yén sadaya komponén aya sateuacan ngamimitian pamasangan:

• UC9050T Wall Control Transmitter
• Pamasangan screws
• Kawat Kacangan

Fitur produk

• Fan 3-Speed Control: Adjust fan speed to High, Medium, or Low.
• Saklar Daya Utama: Turn the fan and light power On or Off with a single button.
• Dimmer Cahaya: Controls the brightness of incandescent lights. For LED bulbs, it typically controls On/Off functionality only.
• 4 DIP Switches: For matching frequency with the ceiling fan receiver.

Gambar: Leuwihview of Eogifee UC9050T Wall Control features, including buttons for High, Medium, Low, Fan Off, Light, and a main On/Off toggle switch.

Setup sareng Instalasi

This section outlines the steps for installing your Eogifee UC9050T Wall Control. This product is a transmitter only and requires an existing compatible receiver in your ceiling fan.

1. Power Disconnection

Before starting any electrical work, ensure the power supply to the ceiling fan circuit is completely disconnected at the main circuit breaker or fuse box. Verify power is off using a voltage panguji.

2. Sambungan Wiring

Connect the wires from the wall control to the corresponding wires in your wall junction box. This device requires a neutral wire at home for proper operation.

• Nyambungkeun Kawat Hideung from the wall control to the Live (hot) wire from the wall.
• Nyambungkeun Lemah Kawat (green or bare copper) from the wall control to the Ground wire from the wall.
• Sambungkeun sésana Kawat Hideung from the wall control to the Neutral wire from the wall.

Image: Diagram showing the connection of black (live), green (ground), and black (neutral) wires from the wall control to the household wiring.

3. Setting DIP Switches

The UC9050T Wall Control uses 4 DIP switches to establish communication with your ceiling fan's receiver. These switches must match the pattern set on your existing ceiling fan receiver or original remote control.

1. Locate the 4 DIP switches on the side of the new wall control.
2. Using a small tool (like a pen or small screwdriver), slide the switches to match the exact ON/OFF pattern of your ceiling fan's receiver or previous remote.
3. If you are replacing an old wall control, match the DIP switch settings from the old unit.

Gambar: Deukeut view of the four blue DIP switches on the side of the wall control, labeled 1, 2, 3, 4, with an 'ON' indicator.

4. Mounting the Wall Control

Once wiring and DIP switch settings are complete, carefully push the wires into the wall box and secure the wall control to the box using the provided screws. Attach the faceplate.

Parentah Operasi

After installation, restore power at the circuit breaker. The wall control is now ready for use.

• Main Power Switch (Toggle): Use the 'OFF' / 'ON' toggle switch at the bottom to turn the entire unit (fan and light) on or off. When in the 'OFF' position, all other buttons are inactive.
• Tombol Laju Kipas:
  • Press 'HI' for high fan speed.
  • Press 'MED' for medium fan speed.
  • Press 'LOW' for low fan speed.
  • Press 'FAN OFF' to turn the fan off.
• Tombol Lampu:
  • Press the 'LIGHT' button to turn the light on or off.
  • For incandescent bulbs, press and hold the 'LIGHT' button to dim or brighten the light. Release at the desired brightness level.
  • For LED bulbs, this button typically functions as an On/Off switch only, unless the LED bulbs are specifically designed for dimming with this type of control.

Image: A hand pressing the 'LIGHT' button on the Eogifee UC9050T Wall Control, installed on a wall in a bedroom with a ceiling fan.

Image: A hand pressing the 'LOW' fan speed button on the Eogifee UC9050T Wall Control, installed on a wall in a living room with a ceiling fan.

Pangropéa

The Eogifee UC9050T Wall Control requires minimal maintenance.

• beberesih: Wipe the surface of the wall control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Pamariksaan: Periodically check the wall control for any signs of damage or loose connections. If any issues are found, disconnect power and address them promptly.

Pamérésan masalah

If you experience issues with your Eogifee UC9050T Wall Control, refer to the following common problems and solutions:

spésifikasi

Garansi sareng Rojongan

Specific warranty information for the Eogifee UC9050T Wall Control is not provided in this manual. For warranty details or technical support, please refer to the product packaging or contact Eogifee customer service directly through their official websitus atanapi pangecér dimana produkna dibeuli.