Paulmann 94453 Capea LED Témbok Luar Ruangan Lamp kalawan Motion Detector Instruksi Manual

Bubuka

Thank you for choosing the Paulmann 94453 Capea LED Outdoor Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image: The Paulmann Capea LED Outdoor Wall Lamp, showing the product itself and its retail packaging. The lamp is black, with a conical shade and an integrated motion sensor at the base.

Parentah Kasalametan penting

• Kasalametan listrik: Installation must be performed by a qualified electrician in accordance with local wiring regulations. Always switch off the main power supply before installation, maintenance, or repair.
• Pamakéan outdoor: This product is designed for outdoor use (IP44 rated). Ensure all connections are properly sealed to prevent water ingress.
• Pamasangan: Mount the fixture securely on a stable surface. Do not install on flammable surfaces.
• Sumber cahaya: The LED light source is integrated and not replaceable by the user. Do not attempt to open or modify the light source compartment.
• Suhu: Ulah nutupan lamp kalayan bahan insulasi. Pastikeun sirkulasi hawa nyukupan sabudeureun fixture nu.

Eusi pakét

Pariksa yén sadaya komponén aya sateuacan ngamimitian pamasangan:

• 1x Paulmann Capea LED Outdoor Wall Lamp (Modél 94453)
• Parentah Majelis
• Mounting hardware (screws, wall plugs) - (Assumed, as typical for wall lamps)

Spésifikasi teknis

Image: Technical drawing showing the dimensions of the Paulmann Capea LED Outdoor Wall Lamp: 153mm width, 165mm height, and 96mm depth.

Guide instalasi

Sateuacan anjeun ngamimitian: Ensure the main power supply to the installation area is switched off at the circuit breaker. Use appropriate tools and safety equipment.

1. Nyiapkeun Lokasi Pasang: Choose a suitable wall location for the lamp, ensuring it is a stable surface and allows for proper wiring. Mark the drilling points for the mounting bracket.
2. liang bor: Bor liang dina titik anu ditandaan teras pasangkeun colokan témbok anu pas (upami diperyogikeun).
3. Bracket Gunung: Ngamankeun bracket ningkatna kana témbok ngagunakeun screws disadiakeun.
4. Wiring: Connect the electrical wires from your mains supply to the terminal block inside the lamp fixture. Ensure correct polarity (Live, Neutral, Earth) and secure all connections tightly. Refer to local electrical codes.
5. Pasang Lamp: Pasangkeun l kalayan ati-atiamp fixture to the mounting bracket, ensuring no wires are pinched. Secure the lamp di tempatna.
6. Mulangkeun Daya: Saatos pamasangan réngsé sareng sadaya sambungan parantos aman, balikkeun deui daya dina pemutus sirkuit utama.

Image: The Paulmann Capea LED Outdoor Wall Lamp shown with its packaging, which illustrates basic installation steps and features like the motion sensor and IP44 rating.

Parentah Operasi

The Paulmann Capea LED Outdoor Wall Lamp features an integrated motion sensor for automatic operation.

Setélan sensor gerak

The motion sensor can be adjusted to suit your specific needs. Typically, there are controls for:

• Sudut deteksi: Approximately 90 degrees.
• Rentang deteksi: 2-8 méter.
• Light Sensitivity (LUX): Determines the ambient light level at which the sensor activates the lamp.
  • ON < 20 Lux: Anu lamp will turn on when motion is detected and the ambient light is below 20 Lux (dark conditions).
  • OFF > 20 Lux: Anu lamp will remain off when the ambient light is above 20 Lux (daylight conditions).
• Waktos ON: Sets the duration the light remains on after motion is detected. Adjustable from approximately 5 seconds to 5 minutes.

Adjust these settings using the small dials or switches located on the motion sensor unit, usually found at the bottom of the lamp. Use a small screwdriver if necessary.

Image: A diagram illustrating the motion sensor's detection angle (90 degrees), range (2-8 meters), and light sensitivity settings (On < 20 Lux / Off > 20 Lux), along with the adjustable time duration (5 seconds - 5 minutes).

Gambar: A close-up view of the integrated motion sensor located at the base of the Paulmann Capea LED Outdoor Wall Lamp, showing its spherical lens.

Pangropéa

• beberesih: Pegatkeun sambungan kakuatan saméméh beberesih. Ngusap lamp kalawan lemes, damp lawon. Ulah make cleaners abrasive atawa pangleyur, sabab ieu bisa ngaruksak finish atawa komponén listrik.
• Sumber cahaya: The LED light source is integrated and designed for long-term use (30,000 hours). It is not user-replaceable. If the LED fails, the entire fixture typically needs replacement.
• Pamariksaan: périodik mariksa lamp for any signs of damage, loose connections, or wear. Address any issues promptly.

Pamérésan masalah

Garansi sarta Rojongan Palanggan

Paulmann products are manufactured to high quality standards. This product comes with a 5-year guarantee, as indicated on the packaging. For warranty claims, technical assistance, or further inquiries, please contact your retailer or Paulmann customer support directly. Keep your proof of purchase for warranty purposes.

For more information, visit the official Paulmann websitus: www.paulmann.com

Émbaran pembuangan

This product contains electronic components and an integrated LED light source. Do not dispose of it with general household waste. Please take it to a designated collection point for electrical and electronic equipment recycling in accordance with local regulations. Proper disposal helps prevent potential negative consequences for the environment and human health.