Peaktech P2170 LCR Meter Instruction Manual

1. Bubuka

The Peaktech P2170 is a digital LCR meter with Equivalent Series Resistance (ESR) measurement capabilities. Designed for both component testing in professional environments and for service and maintenance tasks, its compact design and advanced features ensure precise measurements.

Key features include an illuminated multifunction display with a bargraph and a high measurement frequency of up to 100 kHz. The device also supports PC connectivity for data storage and analysis using the included software.

2. Émbaran Kasalametan

Salawasna merhatikeun pancegahan kaamanan di handap ieu pikeun nyegah tatu atanapi karusakan kana alat:

• Read the entire manual before operating the device.
• Do not operate the meter if it appears damaged or if the insulation is compromised.
• Ensure correct battery installation and replacement.
• Hindarkeun kontak sareng sirkuit hirup nalika nyambungkeun atanapi ngaleupaskeun kabel tés.
• Do not exceed the maximum input ratings specified for each function.
• Tetep alat tetep garing sarta beresih.

3. Produk Langkungview

The Peaktech P2170 LCR Meter is a handheld device designed for measuring inductance (L), capacitance (C), and resistance (R), along with other parameters like ESR, DCR, Dissipation Factor (D), Quality Factor (Q), and Phase Angle (θ).

Gambar 1: Hareupeun view of the Peaktech P2170 LCR Meter, showing the display, function buttons, and input terminals.

3.1 Komponén jeung Asesoris

Paket standar kalebet barang-barang ieu:

• Peaktech P2170 LCR Meter
• kabel panganteur USB
• software PC
• Kelvin clips (test leads)
• Kantong mawa pelindung
• AAA batteries (6x 1.5V)
• Buku pituduh

Figure 2: Peaktech P2170 LCR Meter shown with its included accessories, including Kelvin clips, USB cable, and software CD.

4. Setélan

4.1 Pamasangan batré

The device operates on 6 x 1.5V AAA batteries. To install or replace batteries:

1. Pastikeun méterna pareum.
2. Panggihan panutup kompartemen batré di bagian tukang alat.
3. Open the cover and insert 6 AAA batteries, observing the correct polarity markings.
4. Tutup panutup kompartemen batré aman.

An optional 12V 500mA power adapter can also be used for external power.

4.2 Nyambungkeun Test Leads

Use the provided Kelvin clips for accurate measurements. Connect them to the input terminals as follows:

• Connect the red Kelvin clip to the Hpot jeung Hcur terminal.
• Connect the black Kelvin clip to the Lpot jeung Lcur terminal.
• For 2-wire measurements, connect the test leads to Hpot jeung Lpot.
• Ensure a secure connection to minimize measurement errors.

4.3 Software Installation (PC Link)

The included PC software allows for data logging and analysis. Follow these steps to install:

1. Insert the software CD into your computer's optical drive.
2. Turutan pitunjuk dina layar pikeun ngarengsekeun pamasangan.
3. Connect the meter to your PC using the supplied USB interface cable.
4. Launch the software and establish communication with the device. Refer to the software's help documentation for detailed usage.

5. Parentah Operasi

5.1 Powering on / Pareum

Pencét éta POWER tombol pikeun ngaktipkeun atanapi mareuman méter.

5.2 Modeu pangukuran

The P2170 supports various measurement modes. Press the FUNC button to cycle through the primary measurement parameters:

• Ls (Series Inductance)
• Cs (Series Capacitance)
• Lp (Parallel Inductance)
• Cp (Parallel Capacitance)
• DCR (DC Resistance)
• ESR (Equivalent Series Resistance)
• Rp (Parallel Resistance)
• D (Dissipation Factor)
• Q (Quality Factor)
• θ (Phase Angle)

The illuminated display will show the selected mode and measurement results.

5.3 Measurement Frequency Selection

Pencét éta FREQ button to select the desired test frequency. Available frequencies include 100 Hz, 120 Hz, 1 kHz, 10 kHz, and 100 kHz. The chosen frequency will be displayed on the screen.

5.4 Data Tahan Fungsi

Pencét éta TAHAN button to freeze the current measurement reading on the display. Press it again to release the hold function.

5.5 Kalibrasi

To perform a calibration, ensure no component is connected to the input terminals. Press and hold the KAL button for approximately 2 seconds. Follow any on-screen prompts.

6. Pangropéa

6.1 beberesih

Lap c méternaasing kalawan lemes, damp lawon. Ulah nganggo pembersih atanapi pangleyur anu abrasif. Pastikeun alatna pareum sareng dicabut tina sumber listrik sateuacan dibersihkeun.

6.2 Ngagantian batré

When the low battery indicator appears on the display, replace all 6 AAA batteries as described in Section 4.1.

6.3 Panyimpenan

If the meter is not used for an extended period, remove the batteries to prevent leakage. Store the device in its protective carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Cara ngungkulan

If you encounter issues with your Peaktech P2170, refer to the following common problems and solutions:

• Méterna teu hurung: Check battery installation and ensure batteries are not depleted. Try replacing with new batteries.
• Bacaan teu akurat:
  • Pastikeun lead test disambungkeun leres tur teu ruksak.
  • Perform a calibration (Section 5.5).
  • Verify the correct measurement mode and frequency are selected for the component being tested.
  • Ensure the component is properly connected to the Kelvin clips.
• PC software not connecting:
  • Pariksa sambungan kabel USB.
  • Ensure the software drivers are correctly installed.
  • Restart both the meter and the PC.

If the problem persists, contact Peaktech customer support.

8. Spésifikasi

Detailed technical specifications for the Peaktech P2170 LCR Meter:

Figure 3: Detailed specifications table for the Peaktech P2170 LCR Meter, including measurement modes, ranges, frequencies, and physical characteristics.

9. Garansi jeung Rojongan

For warranty information, technical support, or service inquiries, please contact Peaktech directly or refer to their official websitus. Simpen resi pameseran anjeun salaku bukti pameseran.