Bubuka
This manual provides essential instructions for the safe and effective operation, maintenance, and troubleshooting of your FERM AGM 1042 Angle Grinder. Please read this manual thoroughly before using the tool and keep it for future reference.
Parentah Kasalametan
Salawasna merhatikeun precautions kaamanan dasar pikeun ngurangan résiko seuneu, shock listrik, sarta tatu pribadi.
- Wear appropriate personal protective equipment (PPE) including safety glasses, hearing protection, and gloves.
- Pastikeun workpiece geus aman clampdiurus sateuacan ngamimitian operasi naon waé.
- Tetep wewengkon gawé beresih jeung well-cahayana. Wewengkon nu pabalatak atawa poek ngondang kacilakaan.
- Ulah ngajalankeun parabot kakuatan dina atmosfir ngabeledug, kayaning ku ayana cair kaduruk, gas, atawa lebu.
- Hindarkeun ngamimitian teu kahaja. Pastikeun saklar dina posisi pareum sateuacan dicolokkeun.
- Pegatkeun sambungan colokan ti sumber listrik samemeh nyieun sagala panyesuaian, ngaganti asesoris, atawa nyimpen parabot kakuatan.
- Anggo alat listrik anu pas pikeun aplikasi anjeun. Tong dipaksakeun alatna.
- Jaga alat-alat kalayan ati-ati. Tetep motong alat anu seukeut sareng bersih.
- Jauhkeun murangkalih sareng jalma-jalma nalika ngajalankeun alat listrik.
Produk Leuwihview
Image 1: The FERM AGM 1042 Angle Grinder, showing the main body, auxiliary handle, power cord, and an installed cutting disc with guard.
Komponén
- Cecekelan Utama
- Gagang bantu (bisa dicabut)
- Tombol Konci Spindle
- Hurung/Pareuman Pindah
- Grinding/Cutting Disc Guard
- Spindle
- Kabel listrik
Disetél
Ngagantelkeun gagang bantu
- The auxiliary handle can be screwed into one of the three threaded holes on the gear housing, depending on the application and user preference.
- Pastikeun gagangna geus pageuh pageuh sateuacan dianggo.
Installing/Changing Grinding or Cutting Discs
- Pegatkeun sambungan alat tina catu daya.
- Pencét jeung tahan tombol konci spindle pikeun nyegah spindle ti puteran.
- Use the provided spanner wrench to loosen and remove the outer flange nut.
- Place the desired grinding or cutting disc onto the spindle, ensuring it sits correctly on the inner flange. The disc should be compatible with the tool's specifications.
- Reattach the outer flange nut and tighten it securely with the spanner wrench while holding the spindle lock button.
- Ensure the disc guard is properly positioned to offer maximum protection. Adjust if necessary.
Parentah Operasi
Ngamimitian sareng Ngeureunkeun
- To start the tool, slide the On/Off switch forward. For continuous operation, push the switch further forward until it locks into place.
- To stop the tool, release the switch. If locked, press the rear part of the switch to release it.
Grinding and Cutting
- Always hold the angle grinder firmly with both hands, using the main handle and the auxiliary handle.
- Keunkeun disk nepi ka kecepatan pinuh sateuacan némpél benda kerja.
- For grinding, apply light, even pressure and move the tool smoothly across the surface. Avoid excessive pressure, which can damage the disc and motor.
- For cutting, use a cutting disc and make shallow passes, gradually increasing the depth. Do not twist or bend the disc during cutting.
- Be aware of kickback, especially when cutting. Maintain a firm grip and proper body positioning.
- Saatos dianggo, mareuman alat teras antosan dugi ka disk eureun sapinuhna sateuacan disetel.
Pangropéa
- beberesih: Regularly clean the ventilation slots of the tool to prevent overheating. Use a soft brush or compressed air. Do not use water or chemical cleaners.
- Sikat Karbon: The carbon brushes are wear parts. If the motor sparks excessively or the tool loses power, the brushes may need replacement. This should be done by a qualified technician.
- Kabel listrik: Inspect the power cord regularly for damage. If damaged, have it replaced by a qualified service agent to avoid electrical hazards.
- Panyimpenan: Nyimpen alat dina tempat anu garing sareng aman tina jangkauan barudak.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Alat henteu ngamimitian | Taya catu daya; switch lepat; ari ruksak | Check power connection; Inspect cord; Contact service center |
| Sparking kaleuleuwihan ti motor | Sikat karbon dipaké | Have carbon brushes replaced by a qualified technician |
| Alat overheats | Blocked ventilation slots; Overloading | Clean ventilation slots; Reduce load; Allow tool to cool |
spésifikasi
- merek: Ferm
- Jumlah modél: AGM 1042
- Sumber Daya: Kabel Listrik
- Tipe: Angle coét
- Batré diperlukeun: No
Garansi sareng Rojongan
For warranty information or technical support, please refer to the warranty card included with your product or contact your local FERM service center. Keep your purchase receipt as proof of purchase.
