GODIAG GT102 Power Circuit Probe Tester Manual Pamaké

Bubuka

The GODIAG GT102 Power Circuit Probe Tester is a versatile diagnostic tool designed for automotive electrical systems ranging from 6V to 40V DC. It combines multiple functions including voltmeter, ground test, component activation, short circuit locating, relay testing, and fuel injector testing and cleaning.

Émbaran Kasalametan

• Always wear appropriate personal protective equipment, including safety glasses, when working on vehicle electrical systems.
• Pastikeun kontak kendaraan pareum sateuacan nyambungkeun atanapi nyabut alat uji, kecuali upami aya prosedur uji khusus anu meryogikeun hal anu sanés.
• The GT102 is designed for DC voltage circuits between 6V and 40V. Do not use it on AC voltage or circuits outside this range.
• Hindarkeun noel komponén listrik langsung ku leungeun kosong.
• Do not probe directly into fuel lines or other flammable components.
• The device features overload protection. If the voltage or current exceeds safe limits, the device will automatically shut down to prevent damage.

Eusi pakét

Verify that all items are present in your GODIAG GT102 package:

• GODIAG GT102 Circuit Tester with 20FT Cable
• Battery Hookup Clips
• Relay Test Adapter
• 5pcs Relay Connection Leads
• Suluh Injector Test Lead
• Fuel Injector Cleaning Connector (10mm & 12mm)
• Wire Piercing Probe Set
• Fuel Injector O-Rings & Heat-Shrink Tubes
• Manual pamaké

Disetél

Powering Alat

Connect the red battery hookup clip to the positive (+) terminal of the vehicle's 6-40V DC battery and the black clip to the negative (-) terminal or a good chassis ground. The device will power on and display the current voltage.

Sambungan usik

Insert the test probe into the designated port on the main unit until it clicks securely into place.

Parentah Operasi

Voltmeter Function

Once powered, the GT102 displays the voltage at the probe tip. Touch the probe to any DC circuit point to read its voltage. A red LED indicates positive voltage, and a green LED indicates negative voltage or ground.

Ground Test

To test for a good ground connection, touch the probe to the component or circuit point. If the green LED illuminates and the display shows 0.0V, it indicates a good ground.

Aktipkeun komponén

To activate a component, connect the tester to the vehicle battery. Use the power switch on the tester to supply positive or negative voltage to the probe tip. This allows for safe activation of components like motors, lights, or relays for testing purposes. Ensure the component's voltage and current requirements are within the tester's limits.

Short Locating & Continuity Test

The GT102 can help locate short circuits and test for continuity. By tracing the circuit with the probe, a sudden drop in voltage or a change in LED indication can pinpoint the location of a short. The device's overload protection will activate if a direct short to ground or power is detected, preventing damage. For continuity, if one end of a wire shows current and the other does not, there is a break in the circuit.

Tes Relay

Connect the relay test adapter and appropriate leads to the relay. The GT102 can cycle the relay on and off, allowing you to observe its operation and verify continuity through its contacts. LEDs on the adapter will indicate the status of the relay contacts.

Fuel Injector Test & Clean

Attach the fuel injector test lead and cleaning connector to the injector. For cleaning, connect the cleaning connector to a suitable injector cleaning solution can. Use the dedicated function button on the GT102 to pulse the injector, allowing the cleaning solution to flow through and clear blockages. For testing, the device can activate the injector to check its spray pattern and operation.

Fitur senter

The built-in flashlights illuminate the work area, which is particularly useful in dimly lit engine compartments.

Pangropéa

• Keep the GT102 clean and free from dirt, grease, and moisture. Use a soft, dry cloth for cleaning.
• Store the device and its accessories in a dry, cool place, away from direct sunlight and corrosive materials.
• Regularly inspect cables and connectors for damage. Replace any damaged parts immediately.

Pamérésan masalah

• Alat teu hurung: Check battery connections. Ensure the vehicle battery is within the 6-40V DC range.
• Henteu voltage reading: Verify probe connection. Ensure the probe tip is making good contact with the test point.
• Overload protection activates: This indicates excessive current draw or a direct short. Disconnect the probe, identify and resolve the short circuit before retesting.
• Bacaan teu akurat: Ensure connections are secure and clean. Check for proper grounding of the device.
• Fuel injector not cleaning/testing: Verify all connections to the injector and cleaning solution. Ensure the cleaning solution can is properly attached and has sufficient pressure.

spésifikasi

Garansi sareng Rojongan

For detailed warranty information, technical assistance, or to inquire about replacement parts, please refer to the contact details provided with your original purchase documentation. You may also visit the official GODIAG websitus pikeun sumber pangrojong paling up-to-date.