Bubuka
Thank you for choosing the AZZA LCAZ-240C-ARGB Liquid Cooling System. This manual provides essential information for the proper installation, operation, and maintenance of your new CPU cooler. Please read this manual thoroughly before installation to ensure optimal performance and longevity of your system.
Gambar 1: The AZZA LCAZ-240C-ARGB Liquid Cooling System, featuring a 240mm radiator, two 12cm ARGB fans, and an ARGB pump/cold plate assembly. The fans and pump display vibrant, customizable lighting.
Eusi pakét
Verify that all components are present before beginning installation. If any items are missing or damaged, please contact AZZA support.
- AZZA LCAZ-240C-ARGB Radiator with Pump/Cold Plate Assembly
- Two 120mm ARGB Fans
- Kit Hardware dipasang (pikeun socket Intel sareng AMD)
- Fan and ARGB Splitter Cables
- Témpél termal (diterapkeun atanapi dina tabung)
- Manual pangguna (dokumén ieu)
spésifikasi
| Fitur | Rincian |
|---|---|
| Nomer modél | LCAZ-240C-ARGB |
| Métode Cooling | Liquid (All-in-One) |
| Diaméter kipas | 12 cm |
| Aliran Udara Maksimum | 54 CFM |
| Tekanan hawa maksimum | 1.44 mmH2O |
| Tingkat Noise | 48 desibel |
| Tipe Panyambung Daya | 3-Pin (Pompa), 4-Pin PWM (Kipas) |
| Radiator Dimensions (W x D x H) | 274 mm x 52 mm x 120 mm |
| Warna produk | Hideung |
| Alat nu cocog | Desktop (various Intel/AMD sockets) |
Setup sareng Instalasi
Before proceeding, ensure your computer is powered off and unplugged from the wall outlet. Refer to your motherboard and PC case manuals for specific mounting locations and clearances.
- Nyiapkeun motherboard: Pasang backplate sareng standoff anu pas pikeun soket CPU anjeun (Intel atanapi AMD) kana motherboard.
- Larapkeun Témpél Thermal: If thermal paste is not pre-applied to the cold plate, apply a small, pea-sized amount to the center of your CPU's integrated heat spreader (IHS).
- Mount Cold Plate: Carefully place the pump/cold plate assembly onto the CPU, aligning the mounting holes. Secure it with the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.
- Pasang Radiator sareng Kipas: Attach the two 120mm fans to the radiator using the long screws. Ensure the fan airflow direction is appropriate for your case (intake or exhaust). Mount the radiator assembly to an available fan mount in your PC case (e.g., top, front, or rear).
- Sambungkeun kabel:
- Sambungkeun kabel kakuatan 3-pin pompa kana header AIO_PUMP atanapi CPU_FAN khusus dina motherboard anjeun.
- Connect the two fan 4-pin PWM cables to the included fan splitter cable, then connect the splitter to a CPU_FAN or SYS_FAN header on your motherboard.
- Connect the ARGB cables from the fans and pump to the included ARGB splitter cable, then connect the splitter to a 5V 3-pin ARGB header on your motherboard. Ulah disambungkeun ka header RGB 12V.
- Manajemén Kabel: Route all cables neatly to avoid interference with other components and to improve airflow.
Parentah Operasi
Once installed, the AZZA LCAZ-240C-ARGB operates automatically.
- Daya Hurung: After completing installation and securing all connections, power on your computer.
- Setélan BIOS/UEFI: Access your motherboard's BIOS/UEFI to ensure the CPU_FAN or AIO_PUMP header is set to PWM mode (if applicable) and that fan curves are configured for optimal cooling and noise levels.
- Kontrol ARGB: Use your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize the lighting effects of the fans and pump.
- Monitor Suhu: Use monitoring software to observe CPU temperatures, especially during initial use and under load, to confirm proper cooling performance.
Pangropéa
Regular maintenance helps ensure the longevity and efficiency of your liquid cooling system.
- Ngaleungitkeun lebu: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Dust accumulation can impede airflow and reduce cooling performance.
- Pariksa Tubing: Occasionally check the tubing for any signs of kinks, leaks, or damage.
- Operasi Kipas: Ensure both fans are spinning freely and quietly. Replace any fans that become excessively noisy or stop functioning.
- Operasi pompa: Listen for any unusual noises from the pump. A constant, low hum is normal, but grinding or rattling sounds may indicate an issue.
Pamérésan masalah
If you encounter issues with your AZZA LCAZ-240C-ARGB, refer to the following common problems and solutions.
- Suhu CPU anu luhur:
- Ensure the pump is running and connected to a constant power source (AIO_PUMP header).
- Verify that the cold plate is making proper contact with the CPU and that thermal paste was applied correctly.
- Check that fans are spinning and oriented correctly for optimal airflow through the radiator.
- Ngabersihan sagala akumulasi lebu dina sirip radiator.
- Kipas Teu Diputer atanapi ARGB Henteu Nyaangan:
- Confirm all fan and ARGB cables are securely connected to the motherboard headers and splitters.
- Ensure the ARGB cable is connected to a 5V 3-pin ARGB header, not a 12V 4-pin RGB header.
- Check your motherboard's BIOS/UEFI settings for fan control and ARGB settings.
- Verify that your motherboard's ARGB software is installed and configured correctly.
- Sora Pompa Anu Ahéng:
- Ensure the pump is receiving adequate power.
- Check for air bubbles in the loop by gently tilting your PC case.
- If the noise persists and is disruptive, contact AZZA support.
Garansi sareng Rojongan
AZZA products are designed for reliability and performance. This product comes with a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official AZZA websitus.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact AZZA customer service through their official websitus: www.azza.com.
