Bubuka
This manual provides essential information for the safe and efficient operation of your ProCom MN180TPA-B Natural Gas Ventless Infrared Plaque Heater. Please read all instructions carefully before installation, operation, or maintenance. Retain this manual for future reference.
Gambar: Hareupeun view of the ProCom MN180TPA-B Natural Gas Ventless Infrared Plaque Heater, showcasing its compact design and infrared heating plaques.
Émbaran Kasalametan
Your ProCom heater is designed with safety in mind. It is a ventless unit, meaning it does not require an outside duct or chimney. However, proper ventilation is still crucial for safe operation. This heater is equipped with an Oxygen Depletion Sensor (ODS) that automatically shuts down the unit if oxygen levels become too low. It is ANSI Certified to ensure safety standards are met.
- Always ensure adequate air circulation in the room where the heater is operating.
- Do not obstruct the air intake or exhaust vents of the heater.
- Never use this heater in a recreational vehicle or boat.
- Tetep bahan kaduruk dina jarak aman ti manaskeun.
- Regularly inspect the gas connections for leaks.
Fitur produk
- Infrared Heat Technology: Produces 18,000 Maximum BTU, heating up to 950 sq. ft.
- Ventless Design: No outside duct or chimney required.
- Natural Gas Operation: Designed exclusively for natural gas fuel.
- Kontrol termostat: Allows setting to desired comfort level with High/Medium/Low settings.
- Piezo Ignition: Push-button ignition for easy startup, no electricity or batteries required.
- Sénsor Pangurangan Oksigén (ODS): Automatically shuts off the heater if oxygen levels drop.
- Pamasangan serbaguna: Can be mounted on a wall or placed on the floor using included base feet.
Image: Diagram highlighting key features of the ProCom heater, including BTU output, ventless operation, natural gas compatibility, no electricity requirement, safety features, Piezo ignition, and thermostat mode.
Disetél
The ProCom MN180TPA-B heater offers flexible installation options: wall-mounted or floor-standing.
Ngabongkar sareng Inspeksi
- Taliti miceun sadaya bahan bungkusan.
- Inspect the heater for any shipping damage. Do not install a damaged unit.
- Pastikeun sadaya komponén anu didaptarkeun dina daptar bungkusan aya.
Milih hiji Lokasi
Select a location that allows for proper clearances from combustible materials. Ensure the area has adequate ventilation as per local codes and the heater's specifications.
Pilihan Instalasi
Lantai Nangtung: Attach the included base feet to the bottom of the heater using the provided hardware. Ensure the heater is stable and level.
Pamasangan témbok: Use the included wall mounting bracket and hardware. Follow the detailed instructions in the manufacturer's full installation guide for secure wall attachment and proper clearances.
Image: Components included with the ProCom heater, showing the main unit, base feet, wall bracket, and highlighting the Oxygen Depletion Sensor and natural gas operation.
Image: The ProCom MN180TPA-B heater mounted on a wall in a living space, demonstrating its compact profile and integration into a room.
Sambungan Gas
This heater operates on natural gas only. Connection to the natural gas supply must be performed by a qualified professional in accordance with all local codes and regulations. Ensure all connections are leak-tested before operation.
Parentah Operasi
Follow these steps to safely operate your ProCom MN180TPA-B heater.
Ignition Procedure
- Pastikeun klep suplai gas kabuka.
- Turn the control knob to the 'PILOT' position.
- Press and hold the control knob in while simultaneously pressing the Piezo ignition button repeatedly until the pilot flame ignites.
- Continue to hold the control knob in for approximately 30-60 seconds after the pilot ignites to allow the thermocouple to heat up. Release the knob; the pilot should remain lit.
- If the pilot does not remain lit, repeat steps 2-4.
- Once the pilot is stable, turn the control knob to the desired heat setting (1-5). The main burner will ignite.
Kontrol termostat
The heater features a thermostat control with 5 variable heat settings. Rotate the control knob to select your preferred heat output. The heater will cycle on and off to maintain the set temperature.
Gambar: Deukeut view of the control panel on the ProCom heater, showing the Piezo ignitor button and the rotary knob for 5 variable heat settings and pilot control.
Shutting Down the Heater
- Turn the control knob to the 'OFF' position.
- For prolonged shutdown, close the main gas supply valve to the heater.
Pangropéa
Pangropéa rutin ngajamin umur panjang sareng operasi anu aman tina manaskeun anjeun.
- beberesih: Ensure the heater is completely cool before cleaning. Use a soft, damp cloth to wipe down the exterior. Do not use abrasive cleaners.
- Inspeksi Pilot sareng Burner: Periodically inspect the pilot and burner ports for dust or debris. Clean gently with a soft brush if necessary.
- Sambungan Gas: Annually check all gas connections for tightness and signs of wear.
- Palayanan profésional: It is recommended to have the heater inspected by a qualified service technician at least once a year.
Pamérésan masalah
If you encounter issues with your heater, refer to the following common problems and solutions. For persistent issues, contact a qualified service technician.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Pilot moal hurung | No gas supply; Air in gas line; Pilot orifice clogged; Faulty thermocouple | Check gas supply; Purge air from line; Clean pilot orifice; Contact technician |
| Pilot lights but will not stay lit | Thermocouple not heating sufficiently; Loose thermocouple connection; Faulty ODS pilot assembly | Hold knob longer; Tighten connection; Contact technician |
| Main burner will not ignite | Pilot not lit; Main burner orifice clogged; Low gas pressure | Ensure pilot is lit; Clean burner orifice; Contact gas provider/technician |
| Heater cycles off frequently | Insufficient ventilation; ODS activation; Thermostat setting too high for room size | Increase ventilation; Check for obstructions; Adjust thermostat setting |
spésifikasi
| Atribut | Rincian |
|---|---|
| merek | ProCom |
| Nomer modél | MN180TPA-B |
| Tipe Suluh | Gas alam |
| Maximum BTU Output | 18,000 BTU |
| Panutup pemanasan | Nepi ka 950 sq. |
| Tipe Ignition | Push Button Piezo |
| Tipe Kontrol | Thermostat (High/Medium/Low) |
| Fitur Kasalametan | Sénsor Pangurangan Oksigén (ODS) |
| Pilihan Pamasangan | Wall Mount, Floor Standing (Base Feet Included) |
| Dimensi produk | 8 "D x 22" W x 26" H |
| Item Beurat | 26.2 pon |
| Warna | Bodas |
| Sertifikasi | CSA Certified, ANSI Certified |
Image: Diagram illustrating the dimensions of the ProCom MN180TPA-B heater: 24 inches H, 19 inches L, and 8 inches D.
Émbaran jaminan
For detailed warranty information regarding your ProCom MN180TPA-B Natural Gas Ventless Infrared Plaque Heater, please refer to the warranty card included with your product packaging or visit the official ProCom websitus. Sarat jeung kaayaan jaminan bisa rupa-rupa.
Rojongan Palanggan
If you require assistance, have questions about your heater, or need to report an issue, please contact ProCom customer support. Refer to your product packaging or the official ProCom website for the most current contact information, including phone numbers, email addresses, and online support resources.
