Makerbase MKS Robin Nano V1.2 32-Bit 3D Printer Control Board and TFT35 Touch Screen User Manual

Bubuka

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Makerbase MKS Robin Nano V1.2 32-bit 3D printer control board and the MKS Robin TFT35 V1.0 touch screen. This system is designed to enhance the control capabilities of your 3D printer, offering fast processing speed and support for Marlin2.0 firmware.

Eusi pakét

The MKS Robin Nano V1.2 control board and TFT35 touch screen are available in various configurations. Please verify your package contents against the list below:

Control Board Only: 1x MKS Robin Nano V1.2
Basic Driver Package: 1x MKS Robin Nano V1.2 + 5x A4988 stepper drivers
Advanced Driver Package: 1x MKS Robin Nano V1.2 + 5x TMC2209 stepper drivers
Screen Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen
Screen & Basic Driver Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen + 5x A4988 stepper drivers
Screen & Advanced Driver Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen + 5x TMC2209 stepper drivers
Screen & WiFi Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen + 1x WiFi Module
Screen, Basic Driver & WiFi Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen + 5x A4988 stepper drivers + 1x WiFi Module
Screen, Advanced Driver & WiFi Package: 1x MKS Robin Nano V1.2 + 1x TFT35 touch screen + 5x TMC2209 stepper drivers + 1x WiFi Module

MKS Robin Nano V1.2 control board, TFT35 touch screen, and five A4988 stepper drivers with heatsinks

Image: MKS Robin Nano V1.2 control board, MKS Robin TFT35 V1.0 touch screen, and five A4988 stepper drivers with blue heatsinks. This image illustrates a common package configuration.

Disetél

1. Instalasi Hardware

The MKS Robin Nano V1.2 board is designed for easy integration into 3D printers. Ensure all power is disconnected before proceeding with any hardware installation.

Mounting the Control Board: Secure the MKS Robin Nano V1.2 board within your printer's electronics enclosure using appropriate standoffs and screws.
Connecting Stepper Drivers: Insert the stepper drivers (e.g., A4988, TMC2209) into their designated sockets on the MKS Robin Nano V1.2 board. Pay close attention to the orientation of each driver to prevent damage. Ensure heatsinks are properly attached to the drivers if included.
Motor Panyambung: Connect your stepper motors to the corresponding motor ports (X, Y, Z, E0, E1) on the control board.
Connecting Endstops: Connect your endstop switches to the designated endstop pins.
Connecting Heaters and Thermistors: Connect the hotend and heated bed heaters, along with their respective thermistors, to the appropriate terminals.
Connecting Fans: Connect cooling fans to the fan headers.
Connecting TFT35 Touch Screen: Connect the TFT35 touch screen to the dedicated TFT port on the MKS Robin Nano V1.2 board using the provided cable.
Sasayogian tanaga: Connect your 12V/24V power supply to the main power input terminals of the MKS Robin Nano V1.2 board. Double-check polarity before applying power.

Pahareup-hareup view of the Makerbase MKS Robin Nano V1.2 control board showing various connectors and components

Gambar: A lengkep view of the MKS Robin Nano V1.2 control board, highlighting the various connection points for motors, endstops, heaters, and the TFT screen.

2. Firmware Configuration and Update

The MKS Robin Nano V1.2 supports Marlin2.0 firmware. It is crucial to configure and flash the correct firmware for your specific 3D printer setup.

Unduh Firmware: Obtain the latest Marlin2.0 firmware for MKS Robin Nano from the official Makerbase GitHub repository.
Konfigurasi: Ngarobah nu Configuration.h jeung Configuration_adv.h files within the Marlin firmware to match your printer's kinematics, thermistors, endstops, and other settings.
Flashing Firmware:
1. Compile the modified Marlin firmware using a suitable IDE (e.g., PlatformIO in VS Code).
2. Copy the compiled firmware file (contona, firmware.bin) to the root directory of a FAT32 formatted SD card.
3. Insert the SD card into the MKS Robin Nano V1.2 board's SD card slot.
4. Power on the board. The firmware will automatically update. The screen may show a progress indicator.
5. Once updated, remove the SD card and delete the firmware.bin file to prevent re-flashing on subsequent power-ups.

For detailed instructions and open-source files, please refer to the official Makerbase GitHub repository: https://github.com/makerbase-mks/MKS-Robin-Nano

A video demonstrating the latest firmware V2.0.0 for Robin Nano is available here: https://www.youtube.com/watch?v=Nv3Zgs8XUt4

Parentah Operasi

1. Power On and Initial Boot

After successfully installing the hardware and flashing the firmware, connect the power supply and turn on your 3D printer. The TFT35 touch screen should power on and display the Marlin interface.

MKS Robin TFT35 V1.0 touch screen displaying a file selection interface with folders and G-code files

Image: The MKS Robin TFT35 V1.0 touch screen interface, showing options to select files for printing. This demonstrates the user interface for interacting with the control board.

2. Navigating the TFT35 Touch Screen

The TFT35 touch screen provides an intuitive interface for controlling your 3D printer. Common functions include:

Menu utama: Access various printer functions such as Print, Move, Temperature, Settings, and more.
Print from SD Card: Insert an SD card with G-code files into the TFT35 screen's slot or the MKS Robin Nano board's slot. Navigate to the "Print" menu and select your desired file.
Kontrol Manual: Use the "Move" menu to manually control the X, Y, Z axes and extruders.
Kontrol Suhu: Adjust hotend and heated bed temperatures from the "Temperature" menu.
Setélan: Configure various printer parameters, display settings, and network options (if WiFi module is installed).

3. Using Marlin2.0 Features

With Marlin2.0 firmware, the MKS Robin Nano V1.2 board supports advanced features. Refer to the Marlin documentation for detailed usage of specific functionalities enabled by your firmware configuration.

Pangropéa

Proper maintenance ensures the longevity and reliable operation of your MKS Robin Nano V1.2 control board and TFT35 touch screen.

Tetep Bersih: Regularly clean the board and screen with a soft, dry brush or compressed air to remove dust and debris. Avoid using liquids.
Pariksa sambungan: Pariksa sadaya sambungan kabel sacara berkala pikeun mastikeun éta aman sareng bébas tina korosi.
Pembaruan firmware: Stay updated with the latest firmware releases from Makerbase to benefit from bug fixes and new features.
Kaayaan Lingkungan: Operate the board within recommended temperature and humidity ranges to prevent damage.

Pamérésan masalah

If you encounter issues with your MKS Robin Nano V1.2 board or TFT35 touch screen, consider the following troubleshooting steps:

Henteu aya kakuatan:
- Verify the power supply is connected correctly and providing the correct voltage (12V/24V).
- Check for any blown fuses on the control board.
Screen Not Responding/Blank:
- Ensure the ribbon cable connecting the TFT35 screen to the MKS Robin Nano board is securely seated at both ends.
- Re-flash the TFT firmware if necessary (separate from mainboard firmware).
Motors Not Moving/Incorrect Movement:
- Check motor wiring for correct polarity and secure connections.
- Verify stepper driver installation and orientation.
- Confirm stepper driver current settings are appropriate for your motors.
- Review firmware configuration for correct motor directions and steps per millimeter.
Temperature Reading Errors:
- Check thermistor wiring and ensure they are securely connected.
- Verify thermistor type in firmware configuration.
Masalah Percetakan:
- Ensure G-code files are correctly sliced and compatible with Marlin2.0.
- Check SD card for corruption or formatting issues (FAT32 recommended).

For further assistance, consult the Makerbase GitHub repository or relevant online communities for Marlin firmware and MKS Robin Nano boards.

spésifikasi

Fitur	Rincian
Model Number (Board)	MKS Robin Nano V1.2
Prosesor	32-bit ARM Cortex-M3
Rojongan firmware	Marlin2.0
Stepper Driver Support	A4988, TMC2209, etc. (depending on package)
Rojongan tampilan	MKS Robin TFT35 V1.0 Touch Screen
Masukan Voltage	12V / 24V DC
Konektipitas	USB, SD Card, WiFi (with optional module)
Item Beurat	Approximately 1.76 ounces (50 grams) for the board
Ukuran Paket	1.18 x 0.79 x 0.39 inches (approximate for a single component)
Produsén Jumlah Modél	9875

Rojongan jeung Sumberdaya

For additional information, technical support, and the latest firmware, please refer to the following resources:

Official Makerbase GitHub Repository: https://github.com/makerbase-mks/MKS-Robin-Nano (Contains open-source files, instructions, and firmware.)
Marlin Firmware Documentation: Refer to the official Marlin firmware website for detailed information on configuration and features.
Forum Komunitas: Engage with the 3D printing community for peer support and shared knowledge regarding MKS Robin Nano boards and Marlin firmware.

	Manual Layar Toel MKS TFT35 - Makerbase 3.5 inci Tampilan pikeun Printer 3D Manual pamaké komprehensif pikeun layar rampa Makerbase MKS TFT35, detailing fitur, instalasi, apdet firmware, konfigurasi, sarta rojongan teknis pikeun printer 3D.
	MKS ROBIN Motherboard Manual - Makerbase Manual komprehensif pikeun motherboard MKS ROBIN, rinci fitur, parameter, parentah port, apdet firmware, sarta diagram sambungan sistem pikeun pabrik printer 3D.
	MKS TFT32 Toel layar LCD pikeun printer 3D - Makerbase Jelajahi MKS TFT32, LCD layar rampa warna 32 inci anu serbaguna ti Makerbase, dirancang pikeun panyitak 3D. Diajar ngeunaan fitur na, konektipitas, apdet firmware, outage deteksi, sarta kamampuhan WIFI.
	Makerbase MKS-TFT28 3D Printer Touch Screen LCD: Fitur, Wiring, sareng Pitunjuk Konfigurasi Pituduh komprehensif pikeun Makerbase MKS-TFT28 2.8 inci warna layar toél tampilan LCD pikeun printer 3D. Dokumén ieu rinci ngeunaan fitur-fiturna, kasaluyuan sareng sababaraha papan utama, petunjuk kabel, setélan kakuatan-on, pamutahiran firmware, atanapitagKamampuhan nyimpen, integrasi modul deteksi, kustomisasi poto, sareng konektipitas WiFi, kalebet pilihan kadali jauh via APP, Printrun, sareng Repetier-Host.
	Manual Pamaké MKS DLC32 - Makerbase Manual pamaké komprehensif pikeun dewan controller Makerbase MKS DLC32, ngawengku panganteur hardware, apdet firmware, sarta mode kontrol pikeun printer 3D jeung mesin CNC.
	Manual Pamaké MKS Monster8 V2 - Makerbase 3D Printer Controller Manual pamaké komprehensif pikeun motherboard printer Makerbase MKS Monster8 V2 3D. Nyertakeun panganteur hardware, wiring, konfigurasi firmware (Marlin, Klipper), instalasi, sarta ngungkulan.