Westbrass E507DUS-07 Universal Fit 7-inch Diverter Tub Spout

Bubuka

Thank you for choosing the Westbrass E507DUS-07 Universal Fit 7-inch Diverter Tub Spout. This product is designed for durability and ease of installation, featuring a universal adapter system to accommodate various plumbing configurations. This manual provides essential information for safe installation, proper operation, and effective maintenance to ensure long-lasting performance.

Émbaran Kasalametan penting

• Salawasna pareumkeun suplai cai utama sateuacan ngamimitian padamelan pipa.
• Anggo alat pelindung pribadi anu pas, sapertos kacamata kaamanan sareng sarung tangan, salami instalasi.
• Pastikeun sadaya sambungan aman pikeun nyegah bocor. Ulah overighten.
• Upami anjeun henteu yakin kana léngkah naon waé, konsultasi ka tukang ledeng anu mumpuni.
• Tetep bagian leutik jauh ti barudak.

Eusi pakét

Pariksa yén sadaya komponén aya sateuacan ngamimitian pamasangan:

• 7-inch Diverter Tub Spout (Satin Nickel)
• Pita Teflon
• 1/2-inch Copper Pipe Fitting Adapter
• Brass Adapter (for 1/2-inch IPS or 3/4-inch IPS connections)
• Hex rengkuh
• Extension Nipple (4-inch)

Image: The Westbrass E507DUS-07 tub spout with its diverter button, along with the included Teflon tape, 1/2-inch copper pipe fitting adapter, brass adapter, hex wrench, and 4-inch extension nipple.

spésifikasi

Image: The Westbrass E507DUS-07 tub spout showing its overall length of 7 inches and a base length of 5 3/8 inches, alongside the included installation components.

Gambar: luhur-handap view of the Westbrass E507DUS-07 tub spout, indicating a 7-inch length and 2.5-inch height, with the diverter button visible.

Setup sareng Instalasi

Pakakas Diperlukeun

• Adjustable Wrench or Pipe Wrench
• Screwdriver (if applicable for set screw)
• Teflon Tape (included)
• Hex Wrench (kaasup)

Léngkah-léngkah Instalasi

The Westbrass E507DUS-07 tub spout is designed for universal fit, accommodating 1/2-inch copper, 1/2-inch IPS, or 3/4-inch IPS connections. Follow the steps below based on your existing plumbing.

1. Pareuman suplai cai: Locate and turn off the main water supply to your bathroom or entire house. Open a faucet to relieve pressure.
2. Remove Old Tub Spout: If replacing an existing spout, loosen any set screws on the underside of the spout or unscrew it counter-clockwise from the wall pipe. Clean the area around the pipe.
3. Determine Connection Type: Identify if your existing pipe is 1/2-inch copper, 1/2-inch Male Threaded (IPS), or 3/4-inch Male Threaded (IPS).
4. Nyiapkeun sambungan:
   • For 1/2-inch Copper Pipe Connection: Ensure the copper pipe extends approximately 1-1/2 inches from the wall. Slide the 1/2-inch copper pipe fitting adapter onto the copper pipe. Secure it with the included hex wrench if there's a set screw.
   • For 1/2-inch Male Threaded Connection (IPS): Apply Teflon tape to the threads of the existing 1/2-inch male threaded pipe. Thread the brass adapter onto the pipe.
   • For 3/4-inch Male Threaded Connection (IPS): Apply Teflon tape to the threads of the existing 3/4-inch male threaded pipe.
5. Install Extension Nipple (if needed): If your pipe does not extend far enough from the wall, use the included 4-inch extension nipple. Apply Teflon tape to the threads and connect it to your wall pipe or adapter.
6. Attach Tub Spout:
   • For Slip-On (Copper) or Adapter Connections: Slide the tub spout onto the pipe/adapter assembly until it is flush with the wall. Secure it by tightening the set screw on the underside of the spout with the hex wrench.
   • For Threaded Connections (1/2-inch or 3/4-inch IPS): Carefully thread the tub spout onto the pipe/adapter assembly clockwise until it is hand-tight and properly aligned. Use a wrench for a final snug turn, but do not overtighten.
7. Uji pikeun Bocor: Slowly turn the main water supply back on. Check all connections for leaks. If leaks occur, turn off the water, re-tighten connections, and re-test.

Image: Diagram illustrating four common installation scenarios for the Westbrass E507DUS-07 diverter tub spout, including 1/2-inch copper pipe, 1/2-inch male threaded, 3/4-inch male threaded, and 1/2-inch male pipe with threaded end connections, showing how the adapters and extension nipple are used.

Gambar: Hiji ngabeledug view diagram of the Westbrass E507DUS-07 tub spout, detailing its internal components such as the body, rod, O-rings, knob, gate, insert pipe, bushings, and set screw, along with a parts list.

Parentah Operasi

The Westbrass E507DUS-07 tub spout features a diverter mechanism to switch water flow between the tub spout and a showerhead.

• For Tub Fill: Ensure the diverter knob on top of the spout is in the down position. Water will flow from the tub spout.
• For Shower: Pull the diverter knob upwards. This will redirect water flow to your showerhead. Push the knob down to return water flow to the tub spout.

Pangropéa sareng Perawatan

To maintain the finish and functionality of your tub spout, follow these guidelines:

• beberesih: Clean the spout regularly with a soft cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the satin nickel finish.
• Diverter Maintenance: If the diverter mechanism becomes stiff, a small amount of silicone-based lubricant can be applied to the moving parts.
• Pencegahan bocor: Periodically check for any signs of leaks around the base of the spout. Address any leaks promptly by re-tightening connections or replacing worn seals.

Pamérésan masalah

This section addresses common issues you might encounter with your tub spout.

Garansi sareng Rojongan

Westbrass products are manufactured to high-quality standards. For specific warranty information or technical support, please refer to the official Westbrass websitus atanapi ngahubungan departemén layanan palanggan maranéhna. Simpen resi pameseran anjeun pikeun klaim jaminan.

Kanggo inpormasi sareng produk salajengna, anjeun tiasa nganjang ka Toko Westbrass.