Brio 130SS Series Bottom Load Water Cooler Dispenser

Bubuka

Thank you for choosing the Brio 130SS Series Bottom Load Water Cooler Dispenser. This appliance provides convenient access to hot, room temperature, and cold water from 5-gallon bottles. Designed for ease of use and safety, it features a bottom-loading design to eliminate heavy lifting, a child safety lock for hot water, and an empty bottle alert system. Please read this manual thoroughly before installation and use to ensure proper operation and maintenance.

Émbaran Kasalametan penting

• Kasalametan listrik: Always plug the dispenser into a grounded outlet. Do not use extension cords.
• Hot Water Hazard: The hot water dispenser can reach temperatures up to 194°F (90°C). Exercise extreme caution.
• Kasalametan Anak: Always engage the child safety lock when dispensing hot water, especially in households with children.
• panempatan: Place the dispenser on a flat, level surface away from direct sunlight and heat sources. Ensure adequate ventilation around the unit.
• Setup Awal: After unpacking, allow the unit to stand upright for at least 24 hours before plugging it in and turning it on. This allows the compressor lubricants to settle.
• suplai cai: Use only potable water in 5-gallon bottles. Do not operate the hot or cold water functions without a water bottle installed to prevent dry heating.

Disetél

1. Unpacking sareng Penempatan: Carefully remove the dispenser from its packaging. Place the unit on a firm, level floor surface. Ensure there is at least 4 inches of clearance from the back and sides of the unit to a wall for proper ventilation.
2. Waktu Stand Awal: Allow the water cooler to stand upright for a minimum of 24 hours before plugging it into an electrical outlet.
3. Pamasangan Botol Cai:
   

   Image: A person is shown easily sliding a 5-gallon water bottle into the bottom compartment of the water cooler, demonstrating the bottom-load design.

   • Buka panto lomari handap dispenser.
   • Remove the cap from a new 5-gallon water bottle.
   • Insert the probe assembly into the opening of the water bottle. Ensure the probe is fully inserted and the collar is securely seated on the bottle neck.
   • Slide the water bottle into the bottom compartment and close the cabinet door.
4. Sambungan Daya: Colokkeun kabel listrik kana stop kontak AC 110-120V anu di-ground.
5. Aliran cai mimiti: Before turning on the heating and cooling switches, dispense water from all three taps (hot, room, cold) until water flows steadily. This primes the system and prevents dry heating.
6. Activate Heating and Cooling: Locate the heating and cooling switches on the back of the unit. Flip them to the 'ON' position. The indicator lights on the front panel will illuminate.

Image: A visual guide illustrating the simple three-step process of setting up and using the Brio water cooler.

Parentah Operasi

The Brio 130SS dispenser offers three temperature options: hot, room, and cold water.

Gambar: Detil view of the control panel with LED indicators for hot, cold, and empty bottle, highlighting the child safety lock.

• Dispensing Cai Tiis: Place your cup under the cold water tap. Press the cold water button (usually marked with a snowflake or blue indicator). Release the button when your cup is full.
• Dispensing Room Temperature Water: Place your cup under the room temperature water tap. Press the room temperature button (usually marked with a wave or green indicator). Release the button when your cup is full.
• Ngaluarkeun Cai Panas (kalayan Konci Pangaman Anak):
  

  Image: The dispenser's ample dispense height and deep drip tray are shown, accommodating various cup sizes.

  • Place your cup under the hot water tap.
  • To dispense hot water, simultaneously push the red child safety lock button inward and then press the hot water button (usually marked with steam or a red indicator).
  • Release both buttons when your cup is full. The child safety lock will automatically re-engage.
• Bewara Botol Kosong: The dispenser is equipped with an LED indicator light that illuminates when the 5-gallon water bottle is nearly empty, signaling that a replacement is needed.

Pangropéa

• Ngabersihan Baki Tetes: The drip tray should be emptied and cleaned regularly to prevent overflow and maintain hygiene. Simply slide out the drip tray, empty any collected water, wash with mild soap and water, rinse thoroughly, and replace.
• Bersihan Luar: Wipe the exterior surfaces of the dispenser with a soft, damp lawon. Hindarkeun pembersih abrasive atanapi pangleyur anu tiasa ngaruksak finish.
• Pembersihan/Penghilangan kerak di jero: Periodically, the internal water tanks may require cleaning or descaling. Refer to the full product manual for detailed instructions on this process, which typically involves using a food-grade cleaning solution.

Pamérésan masalah

If you encounter issues not listed here or if solutions do not resolve the problem, please contact Brio customer support.

spésifikasi

Image: The Brio 130SS water cooler with key dimensions, highlighting its streamlined design and no-plumbing requirement.

• Jumlah modél: CLBL130SS
• warna: Beusi sténless
• Bahan: Plastik Hideung
• Kapasitas: 5 Gallons (compatible with 3-5 gallon bottles)
• Jenis pamasangan: Lantai Dipasang
• Ukuran (kira-kira): 44.3 x 15 x 14.3 inci (Pakét Dimensi)
• Beurat barang: 39.5 pon
• kakuatan: AC 110-120V
• Komponén Kaasup: Water Cooler Dispenser, User Manual

Garansi sareng Rojongan

This Brio water cooler dispenser comes with a manufacturer's warranty. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your product or visit the official Brio websitus.

For technical assistance, troubleshooting, or to inquire about replacement parts, please contact Brio customer support. Contact information can typically be found on the product packaging, the official Brio website, or within the full user manual.

Sumberdaya Online: You may find additional support and FAQs on the Brio websitus: Visit the Brio Store