Diagram instalasi

Salawasna pegatkeun sambungan kakuatan saméméh masang atawa ngaganti bohlam sarta saméméh beberesih atawa perawatan séjén.

1. Cabut fixture tina bungkusan aslina.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. Pikeun ngarobah jangkungna fixture, dorong jeung tahan gripper kawat (2g), geser kawat ka panjang nu dipikahoyong lajeng leupaskeun gripper kawat (2g) pikeun ngamankeun (Cabut kaleuwihan kawat lamun perlu)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Jieun sambungan listrik anu pas (hideung ka panas "L", bodas ka nétral "N", taneuh ka "GND") nganggo kacang kawat (1b) disadiakeun dina pakét hardware
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Panjang kawat nada halus upami diperyogikeun, ku cara nyorong sareng tahan gripper kawat (2g) teras saluyukeun kawat ka panjang anu dipikahoyong

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: Teken

LED Wireless parentah operasi kadali jauh

I. Key function of remote control

1. lampu indikator
2. Hurungkeun
3. kacaangan +
4. cahaya tiis
5. siklus
6. Pareuman
7. kacaangan -
8. cahaya haneut
9. lampu peuting

II. Key instructions

Hurungkeun: waktos pondok lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Pareuman: Sakeudeung lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Cahaya tiis +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Cahaya haneut +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp darkens hiji tingkat, Aya 15 tingkat cahaya haneut ti kaluar ka lampu pinuh;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, Aya 11 tingkat kacaangan ti pangluhurna ka panghandapna;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Pencét pondok tombol nightlight, The kacaangan panghandapna tina alamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Catetan: Salah sahiji pemanasan sarta cooling Setélan lampu, Konsumén bisa nangtukeun sorangan nurutkeun catu daya sarta lamps.

III. Functional specifications

Fungsi pemetaan

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 detik. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Fungsi ngabersihan kode

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 detik, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, Pikeun example, dina kasus di handap ieu, kadali jauh jeung lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Anu lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Pareuman pungsi memori

Anggo kadali jauh pikeun nyaluyukeun kacaangan lampu LED, Kacaangan LED lamps jeung nilai kode tina kadali jauh bakal diteundeun dina mémori LED controller sanggeus 15S kakuatan, Power deui sanggeus anjeun geus leungit kakuatan sarta lampu lamp at its previous brightness, And has the code remote control is still controllable.

Dokumén / Sumberdaya

Digilog E27 LED Wireless Remote Control Light Fixture [pdf] Pituduh instalasi E27 LED Wireless Remote Control Light Fixture, E27, LED Wireless Remote Control Light Fixture, Remote Control Light Fixture, Light Fixture, Fixture

Rujukan

• Manual pamaké