KOLINK INSPIRE K8 Midi Tower Case
Manual pamaké
spésifikasi
| Fitur | Rincian |
|---|---|
| Jenis Kasus | Midi Tower |
| Rojongan motherboard | ATX, Micro ATX, Mini ITX |
| Drive Bays | 2 x 3.5", 2 x 2.5" |
| slot ékspansi | 7 |
| Rojongan pendapian | Front: 3 x 120mm, Top: 2 x 120mm, Rear: 1 x 120mm |
| Diménsi | Kira-kira. 200mm x 430mm x 380mm |
Eusi pakét
- Kolink Inspire K8 Case
- Manual pamaké
- Kit aksésori
PITUDUH INSTALASI
Hareup / sisi panyabutan panel
- Candak kaluar panel hareup ku narik taliti ti handap panel.
- Leupaskeun panel sisi kénca ku nyoplokkeun 4 thumbscrews tur angkat panel samping kaca jauh ti wadahna.
- Remove the right side panel bv removing the two rear thumbscrews and sliding the panel backwards.
INSTALASI MOTHERBOARD
- Align motherboard anjeun kalawan chassis pikeun manggihan dimana stand-offs kudu dipasang.
- Sakali rengse, cabut motherboard jeung nyepetkeun stand-offs sasuai.
- Selapkeun motherboard Anjeun 1/0 plat kana cutout di pungkur kasus.
- Teundeun motherboard anjeun kana chassis nu, mastikeun port pungkur cocog kana 1/0 piring.
- Paké screws motherboard disadiakeun pikeun ngagantelkeun motherboard anjeun ka chassis nu.
INSTALASI POWER SUPPLY
- Aace PSU in the bottom rear of the case, within the PSU shroud.
- Align the holes and secure With screws.
KARTU GRAFIK / INSTALASI KARTU PCI-E
- Remove the rear PCI-E slot covers as necessary (depending on the slot size of your card).
- Pasang sacara saksama sareng geser kartu PCI-E anjeun kana tempatna, teras amankeun nganggo sekrup kartu tambihan anu disayogikeun.
2.5" INSTALASI SSD
Secure the supplied SSD screws tc the 2.5″ SSD and then slot into the drop and lock slots on top of the PSU shroud and secure.
3.5″ pamasangan HDD
Secure the supplied HDD screws to the 3.5″ HDD and then slot into the drop and lock slots behind the PSU shroud and secure.
INSTALASI kipas TOP
- Cabut saringan lebu tina luhureun wadahna.
- Align kipas anjeun (s) kana liang screw dina luhureun chassis jeung aman ku screws.
- Ganti saringan lebu anjeun saatos diamankeun.
INSTALASI kipas hareup / tukang
Align kipas anjeun ka liang screw on chassis tur aman kalawan screws.
INSTALASI RADIATOR WATERCOOLING
Secure the fans to the radiator, then fasten the radiator inside the chassis b} with strews from the Outside.
INSTALASI PANEL 1/0
- Carefully check the labelling of each connector from the 1/0 panel to identify their function.
- Rujukan silang sareng manual motherboard pikeun milarian dimana unggal kawat kedah dipasang, teras amankeun hiji-hiji. Mangga pastikeun aranjeunna dipasang dina polaritasna bener pikeun nyegah non-fungsi atawa karuksakan.
FAQ
What motherboards are compatible with the Kolink Inspire K8?
Kasus ngadukung motherboards ATX, Micro-ATX, sareng Mini-ITX.
Sabaraha kipas tiasa dipasang dina kasus éta?
No, fans are not pre-installed. You need to purchase them separately.
Naon panjangna GPU maksimum anu dirojong?
The case supports GPUs up to approximately 330mm in length.
Kumaha kuring ngabersihan saringan lebu?
Remove the filters from the case and clean them with compressed air or wash them with water and let them dry completely before reinstalling.
Dokumén / Sumberdaya
 |
KOLINK INSPIRE K8 Midi Tower Case [pdf] Manual pamaké 04023, ANL-INT, INSPIRE K8 Midi Tower Case, INSPIRE K8, Midi Tower Case, Tower Case, Case |