M5Stack C6LoRA Module User Manual

M5Stamp C6LORA
Model: Stamp C6LoRA
Manual pamaké

Katerangan

Stamp C6LoRa is a high-performance programmable LoRa module designed for the 830 ~ 930 MHz frequency range. The module features an ESP32-C6 SoC, an SX1262 LoRa RF transceiver, and an LNA signal amplifier chip. It comes with two onboard IPEX antenna connectors for external Wi-Fi and LoRa antennas, respectively.
At its core, the ESP32-C6 integrates a rich set of peripheral interfaces, enabling extended functionality through secondary development. It also supports 2.4GHz Wi-Fi 6, offering broader possibilities for IoT applications. Additionally, the module includes a  PI4IOE5V6408 IO expander chip, which is used for LoRa transceiver circuit control and amplifier enable signal management, delivering enhanced power efficiency and providing additional usable IO resources.
A built-in DC-DC converter supports a DC input range of 3.7 to 5V and allows for lithium battery power, making it adaptable to various hardware deployment scenarios. The module is well-suited for long-range communication applications such as smart irrigation, remote metering, and power equipment control.

spésifikasi

Mimitian Gancang

3.1 Persiapan

1. Nganjang ka Arduino resmi websitus tur masang Arduino IDE
   https://www.arduino.cc/en/Main/Software
2. Tambahkeun Manajer Board handap URL ka File → Préferénsi → Manajer Papan Tambahan URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Buka Manajer Papan, milarian "ESP32", teras klik pasang.
4. After installation, select the board “ESP32C6 Dev Module.”
5. Configure the following options. USB CDC On Boot: “Enabled”

3.2 Wi-Fi Test
Pilih mantanampprogram "Examples” → “WiFi” → “WiFiScan”, pilih port anu cocog sareng alat anjeun, teras klik tombol kompilasi sareng unggah di pojok kénca luhur.
Saatos unggah réngsé, buka Serial Monitor pikeun view Inpo scan Wi-Fi.

3.3 BLE Scan
Pilih mantanampprogram "Examples” → “BLE” → ”Scan”, pilih port anu saluyu sareng alat anjeun, teras klik tombol kompilasi sareng unggah di pojok kénca luhur.
Saatos unggah réngsé, buka Serial Monitor pikeun view Émbaran scan BLE.

3.4 LoRa TX
After burning the LoRa test firmware, check the LoRa transceiver information via the ESP32-C6 USB CDC serial port.

Perhatosan FCC

FCC Awas:
Sakur Parobahan atanapi modifikasi anu henteu disatujuan sacara dinyatakeun ku pihak anu tanggung jawab pikeun patuh tiasa ngabatalkeun otoritas pangguna pikeun ngoperasikeun alat.
Alat ieu saluyu sareng bagian 15 tina Aturan FCC. Operasi tunduk kana dua kaayaan di handap ieu: (1) Alat ieu teu tiasa nyababkeun gangguan anu ngabahayakeun, sareng (2) alat ieu kedah nampi gangguan anu ditampi, kalebet gangguan anu tiasa nyababkeun operasi anu teu dipikahoyong.

CATETAN PENTING:
Catetan: Alat ieu geus diuji sarta kapanggih matuh ka wates pikeun alat digital Kelas B, nurutkeun bagian 15 Aturan FCC. Watesan ieu dirarancang pikeun nyayogikeun panyalindungan anu wajar tina gangguan anu ngabahayakeun dina pamasangan padumukan. Alat ieu ngahasilkeun, ngagunakeun, sareng tiasa mancarkeun énergi frekuensi radio sareng, upami henteu dipasang sareng dianggo saluyu sareng petunjuk, tiasa nyababkeun gangguan anu ngabahayakeun kana komunikasi radio. Nanging, teu aya jaminan yén gangguan moal lumangsung dina pamasangan khusus. Upami alat ieu nyababkeun gangguan anu ngabahayakeun kana panarimaan radio atanapi televisi, anu tiasa dipastikeun ku cara mareuman sareng ngaktipkeun alat, pangguna didorong pikeun nyobian ngabenerkeun gangguan ku salah sahiji atanapi langkung tina ukuran ieu:

• Reorient atawa mindahkeun anteneu panarima.
• Ningkatkeun separation antara alat jeung panarima.
• Sambungkeun alat-alat kana stop kontak dina sirkuit béda ti nu disambungkeun ka panarima.
• Taroskeun ka dealer atanapi teknisi radio/TV anu berpengalaman pikeun pitulung.

Pernyataan Paparan Radiasi FCC: Alat-alat ieu saluyu sareng wates paparan radiasi FCC anu ditetepkeun pikeun lingkungan anu teu terkendali.

Catetan penting:
Upami kaayaan ieu teu tiasa dicumponan (sapertos example, konfigurasi laptop tangtu atawa co-lokasi kalawan pamancar sejen), lajeng otorisasina FCC geus euweuh dianggap valid, sarta ID FCC teu bisa dipaké dina produk ahir. Dina kaayaan ieu, integrator OEM bakal tanggung jawab pikeun ngevaluasi deui produk ahir (kaasup pamancar) sareng kéngingkeun otorisasi FCC anu misah.

Labeling Produk Tungtung
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

Inpormasi Manual ka Pamaké Ahir
OEM integrator kudu sadar teu nyadiakeun informasi ka pamaké tungtung ngeunaan kumaha carana install atawa nyabut modul RF ieu dina manual pamaké ngeunaan produk tungtung nu integrates modul ieu.
Manual pamaké tungtung wajib ngawengku sakabéh informasi pangaturan / warnings sakumaha ditémbongkeun dina manual ieu.

Parentah integrasi pikeun pabrik produk host nurutkeun KDB 996369 D03 OEM Manual v01

2.2 Daptar aturan FCC lumaku
CFR 47 FCC PART 15 SUBPART C geus ditalungtik. Ieu lumaku pikeun pamancar modular.

2.3 Kaayaan pamakéan operasional husus
Modul ieu mangrupikeun modul anu mandiri. Upami produk ahirna bakal ngalibetkeun sababaraha kaayaan transmisi sacara simultan atanapi kaayaan operasional anu béda pikeun pemancar modular anu mandiri dina hiji host, produsén host kedah konsultasi sareng produsén modul pikeun metode pamasangan dina sistem ahir.

2.4 Prosedur modul kawates
Henteu tiasa dianggo

2.5 Ngalacak desain anteneu
Henteu tiasa dianggo

2.6 pertimbangan paparan RF
The device has been evaluated to meet the general RF exposure requirements. The device can be used in mobile or fixed exposure conditions with a minimum distance of 20 cm between the radiator & user’s body.

2.7 Anteneu
This radio transmitter has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.8 Labél sareng inpormasi patuh
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

2.9 Inpormasi ngeunaan modeu tés sareng syarat tés tambahan
The host manufacturer that installs this module with limited modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result complies with FCC part 15.247 and 15.209 requirements, then the host can be sold legally.

parentah integrasi pikeun pabrik produk host nurutkeun KDB 996369 D03 Manual OEM v01

2.10 Tés tambahan, Bagian 15 Bantahan Subpart B
This transmitter module is tested as a subsystem, and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rule requirements if applicable.

2.11 Catetan Pertimbangan EMI
We recommend using “best practice” RF design engineering, testing, and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.

2.12 Kumaha Jieun Parobahan - Catetan Penting
Upami kaayaan ieu teu tiasa dicumponan (sapertos example, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, OEM integrator contacts Grantees to make permissive changes, or the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Salami sadaya kaayaan di luhur kacumponan, tés pamancar salajengna moal diperyogikeun. Tapi, integrator OEM tetep tanggung jawab pikeun nguji produk ahirna pikeun sarat patuh tambahan anu diperyogikeun sareng modul ieu dipasang.