SoliTek SOLID Series Solar Modules Installation Guide

SoliTek SOLID Series Solar Modules

Parentah Pamakéan

• Read this guide entirely before installation.
• This document provides minimum requirements and recommendations for safe and successful installation of SoliTek PV modules and is necessary to retain compliance with IEC 61215, IEC 61730, and UL 61730 standards.
• This guide provides basic information on JSC SoliTek Cells SOLID series photovoltaic modules, including their installation and safe handling.
• All instructions should be read and understood before attempting installation. Contact your dealer or JSC SoliTek Cells for further information if needed.
• This documentation refers to the PV modules themselves and is not a comprehensive installation manual for personnel not specifically trained in PV modules.
• It serves as a general but strictly mandatory reference for the installer. Infringement or inaccurate observance of any clause in this documentation voids the warranty.
• The installer must understand and follow all applicable local, state, and federal regulations and standards for building construction, electrical design, fire, and safety.
• Check with local authorities for permitting requirements before installing or maintaining PV modules, and become familiar with mechanical and electrical requirements for photovoltaic systems.
• Gagalna nuturkeun paréntah dina pituduh ieu tiasa ngaruksak komponén sistem, ngabahayakeun tanaga, ngaruksak harta benda, atanapi ngabatalkeun jaminan panel.
• Rooftop PV systems should only be installed on dwellings formally analyzed for structural integrity and confirmed to be capable of handling the additional weighted load of PV system components (including PV modules) by a certified building specialist or engineer.

SYARAT UMUM

• Mangga baca pituduh ieu sagemblengna saméméh pamasangan.
• Tujuan tina dokumén ieu nyaéta pikeun nyayogikeun syarat minimum sareng saran pikeun pamasangan modul SoliTek PV anu aman sareng suksés.
• Dokumén ieu ogé ngandung sarat anu dipikabutuh pikeun ngajaga modul SoliTek PV patuh kana standar IEC 61215, IEC 61730, UL 61730.
• Buku ieu ngandung émbaran dasar ngeunaan JSC "SoliTek Sél" modul photovoltaic runtuyan SOLID, instalasi maranéhanana sarta penanganan aman. Sadaya parentah kedah dibaca sareng kahartos sateuacan nyobian pamasangan. Mun aya patarosan, mangga ngahubungan dealer Anjeun atawa JSC "SoliTek Sél" kanggo inpo nu salajengna.
• This documentation refers to the PV-modules themselves and is not meant to be a complete installation manual for personnel not specifically trained to PV-modules.
• It serves as a general but strictly mandatory reference for the Installer.
• Pelanggaran atanapi katepatan anu teu leres tina klausa tina dokuméntasi ieu ngabatalkeun jaminan.
• Pamasang kedah ngartos sareng nuturkeun sadaya peraturan lokal, nagara, sareng féderal sareng standar pikeun pangwangunan gedong, desain listrik, seuneu, sareng kaamanan, sareng kedah parios ka otoritas lokal pikeun nangtoskeun syarat ijin anu tiasa dianggo sateuacan nyobian masang atanapi ngajaga modul PV sareng kedah jadi akrab jeung sarat mékanis jeung listrik pikeun sistem photovoltaic.
• Gagalna nuturkeun paréntah dina pituduh ieu tiasa ngaruksak komponén sistem, ngabahayakeun tanaga, ngaruksak harta benda, atanapi ngabatalkeun jaminan panel.
• Sistem PV rooftop ngan kudu dipasang dina dwellings nu geus formal dianalisis pikeun integritas struktural jeung dikonfirmasi sanggup nanganan beban beurat tambahan komponén sistem PV, kaasup modul PV, ku spesialis wangunan Certified atawa insinyur.
• For your safety, do not attempt to work on a rooftop until safety precautions have been identified and taken, including, without limitation fall protection measures, ladders or stairways, and personal protective equipment (PPE).
• For your safety, do not install or handle PV modules under adverse conditions, including, without limitation strong or gusty winds, and wet or frosted roof surfaces.
• Konstruksi modul PV pelat datar diwangun ku assembly laminated sél surya encapsulated dina bahan insulating dina dua lembar kaca.
• Simpen dokuméntasi ieu dina tempat anu aman pikeun rujukan ka hareup.
• Ulah nyobian ngabongkar modul, sarta ulah dipiceun sagala nameplates napel atawa komponén! Lakukeun kitu bakal batal jaminan.

Penanganan & Aplikasi

nanganan

• SoliTek PV modules must be transported in the supplied packaging only and kept in the packaging until they are ready to be installed.
• Protect pallets against movement and exposure to damage during transportation. Secure pallets from falling over.
• Ulah ngaleuwihan jangkungna maksimum pallets pikeun ditumpuk, sakumaha dituduhkeun dina bungkusan palet.
• Store pallets in a cool and dry location until the PV modules are ready to be unpackaged.
• SoliTek PV modules are heavy and should be handled with care. Never use the junction box or cables as a grip.
• Do not exert mechanical stress on the cables.
• Never step on PV modules or drop or place heavy objects on them.
• Be careful when placing PV modules on hard surfaces and secure them from falling.
• Broken glass can result in personal injury. PV modules with broken glass cannot be repaired and must not be used.
• Broken or damaged PV modules must be handled carefully and disposed of properly.

APLIKASI

Watesan

• SoliTek PV modules must be mounted on appropriate mounting structures positioned on suitable buildings, the ground, or other structures suitable for PV modules (e.g. carports, building facades or PV trackers).
• PV modules must not be mounted on moving vehicles of any kind. Modules must not be installed in locations where they could be submerged in water.
• Do not install modules above 2000 m (6561 ft) altitude above sea level
• Lampu artifisial kentel teu kudu diarahkeun kana modul SoliTek PV.

Rekomendasi

• SoliTek nyarankeun yén modul PV dipasang dina sudut Dengdekkeun minimum 10 derajat pikeun ngidinan pikeun beberesih diri ditangtoskeun tina hujan.
• Shading parsial atanapi lengkep tina modul atanapi modul PV tiasa sacara signifikan ngirangan kinerja sistem.
• SoliTek nyarankeun ngaminimalkeun jumlah tempat teduh sapanjang taun pikeun ningkatkeun jumlah énergi anu dihasilkeun ku modul PV.
• Sistim luhur voltages could be induced in the event of an indirect lightning strike, which could cause damage to PV system components.
• The open area of wire loops should be minimized in order to reduce the risk of lightning-induced voltage lonjakan.
• Ventilasi modul anu langkung saé sareng kabel sambungan anu langkung pondok ningkatkeun produksi énergi listrik.

Pikeun modul bifacial:

• Disarankeun ningkatkeun jangkungna panel PV tina taneuh supados langkung seueur cahaya tiasa ngarambat handapeun modul teras ngeunteung
• Keuntungan bifacial naek sacara signifikan upami modul dipasang di luhur bodas (nilai albedo tinggi), permukaan anu ngagambarkeun cahaya.

Pamasangan listrik

Kasalametan

• modul PV bisa ngahasilkeun arus jeung voltage lamun kakeunaan cahaya tina sagala inténsitas. Arus listrik nambahan kalayan inténsitas cahaya anu langkung luhur. DC voltage tina 50 Volts atawa saluhureuna berpotensi bisa nepi ka tiwasna. Ngahubungan sirkuit langsung tina sistem PV anu beroperasi dina lampu tiasa nyababkeun kejutan listrik anu maot.
• De-énergize modul PV ku nyoplokkeun aranjeunna sagemblengna tina lampu atawa ku nutupan beungeut hareup maranéhanana jeung bahan opak. Ngeunaan peraturan kaamanan pikeun alat listrik hirup nalika damel sareng modul anu kakeunaan cahaya naon waé. Anggo alat anu diisolasi sareng ulah ngagem perhiasan logam nalika damel sareng modul PV.
• Pikeun ngahindarkeun busur sareng shock listrik, ulah pegatkeun sambungan listrik dina beban. Sambungan anu salah ogé tiasa nyababkeun busur sareng kejutan listrik. Tetep panyambungna garing sarta beresih jeung mastikeun yén maranéhna aya dina kaayaan kerja ditangtoskeun. Ulah nyelapkeun obyék logam kana konektor atawa ngaropéa aranjeunna dina sagala cara pikeun ngamankeun sambungan listrik.
• Do not touch or handle PV modules with broken glass unless the PV modules are first disconnected, and you are wearing proper PPE. Avoid handling PV modules when they are wet unless cleaning the PV modules as directed in this manual. Never touch electrical and wet connections without protecting yourself with insulated gloves.
• The modules are qualified for Class II protection against electrical shock, in accordance with clause 4 of IEC 61730-1:2016, which can be used in systems operating at > 50 V DC or >240 W, where general contact access is anticipated and modules qualified for safety through UL 61730 within this application class are considered to meet the requirements of Safety Class II.
• Masang sistem photovoltaic surya merlukeun kaahlian jeung pangaweruh husus. Ieu kudu dilaksanakeun ngan ku tanaga mumpuni sarta maréntahkeun husus. Pamasang nganggap sagala résiko tatu, kalebet résiko kejutan listrik.
• Paké ngan parabot, konektor, wiring jeung hardware ningkatna husus dirancang pikeun pamakéan dina sistem photovoltaic.
• Before any manipulation at an installed PV plant, switch it off first on the AC-side, and then on the DC side of the inverter or the charge controller.
• Nalika megatkeun sambungan kabel nu disambungkeun ka modul photovoltaic nu kakeunaan lampu, hiji busur listrik bisa lumangsung. Arcs bisa ngabalukarkeun kaduruk, ngamimitian seuneu, atawa lamun heunteu nyieun masalah kaamanan (nepi ka shock listrik bisa nepi ka tiwasna).
• Pariksa keur sésana voltage before starting and observe the local safety-relevant regulations for such working conditions.
• Dina kaayaan normal, modul photovoltaic bisa ngahasilkeun leuwih arus jeung / atawa voltage (di dieu: 30V DC) ti dilaporkeun dina kaayaan test baku.
• Kontak sareng DC voltag30 V atawa leuwih berpotensi picilakaeun. Ati-ati nalika kabel atanapi nanganan modul anu kakeunaan sinar panonpoé.
• Ngan sambungkeun modul sareng arus kaluaran anu dipeunteun sami dina séri. Mun modul disambungkeun dina runtuyan, total voltage sarua jeung jumlah tina modul individu voltages.
• Ngan nyambungkeun modul atawa kombinasi runtuyan modul jeung vol saruatage in parallel. If modules are connected in parallel, the total current is equal to the sum of the individual module or series combination currents.
• Salawasna nganggo jinis modul anu sami dina sistem photovoltaic khusus.
• If the sum of short circuit currents of the parallel-connected modules exceeds the reverse current, string diodes or fuses have to be used in each string of modules connected in parallel. These string diodes or fuses have to be qualified for the maximum expected current and voltage. The fuse rating value is also corresponds to the maximum reverse current that a module can withstand. The reverse current value can be found on the product label, in the product datasheet or in chapter 8 of the installation manual. Observe the instructions and safety precautions for all other components used in the system, including wiring and cables, connectors, DC-breakers, inverters, etc.
• Paké parabot kaamanan luyu (parabot insulated, sarung diéléktrik, sapatu jeung sajabana) disatujuan pikeun pamakéan dina pamasangan listrik.

KONFIGURASI

• Dina kaayaan normal, modul photovoltaic kamungkinan ngalaman kaayaan anu ngahasilkeun leuwih arus jeung / atawa voltage than reported at Standard Test Conditions (STC: 1000 W/ m2, AM 1.5, and 250C/770F cell temperature) or Bifacial nominal power index(BNPl front irradiance 1000 W/m2, back irradiance 135 W/m2 AM 1.5, and 25 OC/770F cell temperature). The short-circuit current (ISC) should be multiplied by a factor of 1.25 and the open-circuit voltage (VOC) kudu dikalikeun ku faktor nepi ka 1.25 dumasar kana suhu ambient panghandapna jeung pangluhurna dirékam pikeun lokasi pamasangan nalika nangtukeun vol komponén.tagratings, ratings arus konduktor, ukuran sekering, sarta ukuran kontrol disambungkeun ka kaluaran PV.
• Voltages mangrupakeun aditif nalika modul PV disambungkeun langsung dina runtuyan, sarta arus modul aditif nalika modul PV disambungkeun langsung dina paralel. modul PV kalawan ciri listrik béda teu kudu disambungkeun langsung dina runtuyan. Pamakéan alat éléktronik pihak-katilu anu cocog sareng modul PV tiasa ngaktifkeun sambungan listrik anu béda-béda sareng kedah dipasang saluyu sareng parentah produsén.
• Vol maksimumtage of serial interconnection of the modules must be less than the maximum certified module’s system voltage. Ogé, input maksimum voltage tina inverter sareng alat listrik anu sanés dina sistem kedah dipertimbangkeun. Sirkuit kabuka voltage of the array string needs to be calculated at the lowest expected a mbient temperature forthe location. The maximal system voltage for the module is indicated in the module’s datasheet.
• Accordingly, for BLACKSTAR, SOLID or MAGNUS series modules, the values of ISC and VOC under STC or BNPI marked on this module should be multiplied by a factor of 1,25 when determining component voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. In the USA, referto Section 690-8 of the National Electrical Code (N EC) for an additional multiplying factor of 125 percent (80 percent de-rating) which may be applicable.

ALAT LINDUNGAN ARUS (OCPD)

• When the potential reverse current of a PV string exceeds the rated SoliTek PV module series fuse rating (values indicated at the module datasheet) an overcurrent protection device (OCPD) must be used.
• An overcurrent protection device is required for each series string if more than two series are connected in parallel.
• In this case, it is needed to use one fuse per string rated at 1.25 x Isc or higher (Isc is the PV module’s short circuit current at STC). A PV fuse on each PV string will protect the PV modules and conductors from overcurrent faults and help minimize any safety hazards.
• The PV fuse will also isolate the faulted PV string so the balance of the PV system can continue to generate electricity.
• sekering amp rating ≥ 1.25 x Isc
• Pilih rating standar anu langkung luhur salajengna dina katalog PV Fuses anu sayogi.
• Isc = Arus sirkuit pondok tina hiji modul dina Kaayaan Uji Standar (STC).
• Mertimbangkeun nilai Isc of SoliTek modul, nilai katuhu tina PV Fuses pikeun dipaké dina instalasi nyaeta 30 A. SoliTek nyarankeun ngagunakeun PV fuses boh konduktor positif jeung negatif.

KABEL & KABEL

modul PV SoliTek disadiakeun dua baku, kabel kaluaran sinar-cahaya nu terminated kalawan panyambungna PV siap pikeun paling pamasangan. Positip (+) terminal boga konektor jalu sedengkeun négatip (-) terminal boga konektor bikang. The wiring modul dimaksudkeun pikeun sambungan runtuyan (ie, jalu (+) ka bikang (-) interkonéksi) tapi ogé bisa dipaké pikeun nyambungkeun alat-alat listrik pihak-katilu cocog nu mungkin gaduh konfigurasi wiring alternatif salami parentah produsén urang dituturkeun.
Paké wiring widang kalawan aréa cross-sectional cocog nu disatujuan pikeun pamakéan dina arus pondok-circuit maksimum modul PV. Kabéh kabel kudu insulated ganda, kabel cross-linked kalawan rating minimum 1,8 kV (leuwih 1500 V vol.tage) jeung suhu dipeunteun minimum 90 ˚C (190 ° F). Ukuran kawat teu kurang ti 4 mm² (12 AWG). Jinis insulasi kedah cocog sareng jinis metode pamasangan anu dianggo sareng kedah nyumponan syarat IEC 61730 sareng Kasalametan Kelas II.

• Tingkat insulasi: 1,8 kV (konduktor-konduktor).
• Suhu: -40°C nepi ka +90°C (-40 °F nepi ka 190 °F) sahenteuna.
• Pangwangunan konduktor: kawat tambaga terdampar tinned kalayan purity tambaga leuwih gede ti 99,9%.
• insulasi primér: cross-linked poliétilén (XLPE), cahya panonpoé jeung tahan Uap, retardant seuneu. Cocog jeung conduit na raceways dipasang di jero taneuh.
• Insulasi (jaket): termoplastik, tahan sinar panonpoé, tahan seuneu, tahan cai.
• Diaméter luar kabel minimum sareng insulasi - 5,2 mm (2,05 inci).
• Penampang konduktor minimum - 4 mm² (12 AWG).

SoliTek nyarankeun pamasang ngan ukur nganggo kabel anu tahan sinar panonpoé anu mumpuni pikeun kabel arus searah (DC) dina sistem PV. Kabel kudu dibenerkeun kana struktur ningkatna ku cara nu ruksakna mékanis kabel jeung / atawa modul dihindari. Ulah nerapkeun stress kana kabel. Pikeun ngalereskeun, paké cara anu pas, sapertos ikatan kabel anu tahan sinar panonpoé sareng/atawa klip manajemén kawat. Nalika kabelna tahan sinar panonpoé sareng tahan cai, upami mungkin, hindari paparan sinar panonpoé langsung sareng cai immersion kabel.
Panjang standar kabel tina kotak simpang nyaéta 1,2 m (47,24 inci). Ieu dimaksudkeun yén dua panels bakal interconnect dina sistem.

NGASAR

• Module grounding must be done in accordance with the electrical design and construction specifications, procedures, regulations and other special grounding requirements applicable to the installation sites. If grounding is needed, it should be done accordingly:

Framed type modules grounding
Liang ditandaan ku tanda grounding dina pigura ngan bisa dipaké pikeun grounding. Ulah bor liang grounding tambahan dina pigura modul.
The grounding conductor or strap may be copper, copper alloy, or any other material acceptable foruse as an electrical conductor in accordance with local electric codes and regulations.
Konduktor grounding teras kedah ngadamel sambungan ka bumi nganggo éléktroda taneuh bumi anu cocog.
A bolted connection is required; it incorporates:

• Ukuran baut M4.
• A washer huntu handapeun sirah baud atawa baud serrated kudu nembus coatings nonconductive kawas pigura anodized.
• Nut nyepetkeun cocog pikeun baud M4.
• Sadaya hardware kedah tina logam nonferrous, 300-seri stainless steel, atanapi suitably ditangtayungan korosi.
• Torsi anu disarankeun pikeun ngonci mur nyaéta 2 Nm÷2.2 Nm (1,48÷1,62 ft-lb).
• Grounding bolt kudu ngaliwatan sagala elemen nyambungkeun.

• Alat-alat anu didaptarkeun sareng diidentifikasi pikeun grounding pigura logam tina modul PV diidinan pikeun taneuh pigura logam kakeunaan modul ka grounded struktur ningkatna.
• In any case the grounding screws or other parts have to be used separately from the mounting parts of the module.
• Alternate grounding options built through the mounting system are acceptable as long as they have been IEC and UL approved.
• Grounding resistance of the grounding structure shall be reached according to local regulations, Eurocodes, or other legal normative references.

Frameless type modules grounding

• Due to that modules are without frame, grounding is not forseen. Other PV plant equipment should be grounded according to the local and national electrical codes.

Panyambung

• Connectors for SoliTek PV panels are Stäubli MC4-Evo 2. Keep connectors dry and clean and ensure that connector caps are hand-tight before connecting the modules.
• Ulah nyobian nyieun sambungan listrik kalawan panyambungna baseuh, kotor, atawa lamun heunteu faulty.
• Hindarkeun paparan sinar panonpoé sareng immersion cai tina konektor. Hindarkeun panyambungna dina taneuh atanapi permukaan hateup.
• Do not disconnect under load. Faulty connections can result in arcs and electrical shock.
• Pariksa yén sadaya sambungan listrik geus aman fastened. Pastikeun yén sadaya panyambungna ngonci pinuh aktipitas tur dikonci.

DIODA BYPASS

The PV module’s junction box contains 3 bypass diodes (one in each part of split junction box; Schottky type) connected in parallel with the PV cell strings. In the case of partial shading (hot-spot effect), the diodes bypass the current generated by the non-shaded cells, therebylimiting module heating and performance losses.
Dioda bypass sanes alat panyalindungan arus leuwih. Dioda bypass ngalihkeun arus tina senar sél upami aya bayangan parsial. Ciri-ciri dioda ieu:

• Voltage rating - 50 V.
• Peunteun ayeuna - 25 A.

Seuneu kelas rating

• Modul SoliTek SOLID Bifacial sareng Blackstar parantos disatujuan ku uji seuneu IEC sareng ngahontal Flammability Kelas A. Ujian seuneu dilakukeun dina inclination 127 mm (5 inci) per 300 mm (11,81 inci), sakumaha anu ditunjuk dina titik A.2.5 tina IEC 61730-2.
• SoliTek SOLID Bifacial has fire rating of 28 according to UL1703-2 standard. SoliTek Blackstar has fire rating of 29 according to UL1703-2 standard.

Ningkatna mékanis

• The mechanical loads described in this manual are the test loads.
• For calculating the equivalent maximum design loads, a safety factor of 1.5 (Design load×1.5 safety factor=Mechanical test load) needs to be considered in compliance with the requirements of the local laws and regulations.

SYARAT UMUM

• Modules can be mounted in landscape or portrait orientation. For the bifacial modules, in order to get notable bifacial gain, the distance between the bottom of the modules and the roof or ground surface shall be at least 0,8 m (31,50 inch).
• Also, the bifacial gain increases significantly if modules are installed above white, light-reflecting surfaces (under surfaces with high albedo value).
• If the mounting rails are installed across the module, the bifaciality effect will be lower due to back-side cells shading.
• Punten perhatoskeun peraturan kaamanan sareng petunjuk pamasangan anu kalebet dina sistem pamasangan. Upami diperlukeun, mangga ngahubungan supplier langsung pikeun informasi salajengna.
• The modules must be safely set onto the mounting rail.
• The whole rail supporting the photovoltaic system must be strong enough to resist potential mechanical pressures caused either by wind or snow, in accordance with local, regional and state safety (and other associated) standards.
• The mounting system shall be tested and inspected by a third-party testing institution with static mechanical analysis capacity in accordance with local national standards or international standards.
• Before installing modules on a roof, ensure that the roof construction is suitable.
• In addition, any roof penetration required to mount the modules must be properly sealed to prevent leaks.
• Pastikeun yén rel ningkatna moal deform atanapi mangaruhan modul lamun expands salaku hasil tina ékspansi termal.
• The module can appear thermal expansion and cold contraction; thus, the interval between two adjoining modules shall be no lesser than 10 mm (0,39 inch).
• Ulah nyobian bor liang dina beungeut kaca jeung pigura tina modul sakumaha ieu bakal batal jaminan.
• The mounting method must not result in the direct contact of dissimilar metals with the aluminum frame of the modules that will result in galvanic corrosion.

Komponén ningkatna kedah didamel tina bahan anu awét, anti korosi sareng tahan UV (baja tahan karat sareng komponén aluminium anodized disarankeun).

MOUNTING sareng CLAMPS

• Paké sahenteuna 4 laminate clamps pikeun ngalereskeun modul dina rel ningkatna. Modul clamps bagian logam teu kudu datang kana kontak jeung kaca hareup atawa tukang. Lamun milih tipe ieu clamp-metoda ningkatna, ngagunakeun sahanteuna opat clamps dina unggal modul; dua clamps kudu napel dina unggal sisi panjang. Gumantung kana angin lokal jeung beban salju, cl tambahanamps bisa jadi diperlukeun pikeun mastikeun yén modul bisa nanggung beban.
• Clamps tightening torsi kedah sahenteuna 15 Nm (11,06 ft-lb), tapi teu leuwih gede ti 20 Nm (14,75 ft-lb). Biasana, 15 Nm (11,06 ft-lb), ngahontal nalika dua aluminium profiles touch silih. Nalika modul dipasang dina orientasi potret dina hateup pitched nu boga > 45 ° lamping, hook tambahan di handapeun modul diperlukeun.

SOLID Black, Semi-clear, Satin, Agro Frameless

Kalayan rel transversal

BLACKSTAR, SOLID Black 35(40) mm, SOLID Semi-clear 35(40) mm, SOLID Satin 35(40) mm, SOLID Agro 35(40) mm, Magnus Framed mounting

• Lamun milih tipe ieu clamp-metoda ningkatna, ngagunakeun sahanteuna opat clamps dina unggal modul; dua clamps kudu napel dina unggal sisi modul. Modul clamps teu kudu datang kana kontak jeung kaca hareup jeung teu kudu deform pigura.
• Pastikeun pikeun nyingkahan épék bayangan dina sél surya tina modul clamps.
• The module frame is not to be modified under any circumstances. Do not to block the drain hole of the frame.
• Panjangna clamp should be at least 30 mm (1,18 inch).
• clamp kudu tumpang tindih pigura modul ku sahanteuna 5 mm (0,2 inci), tapi teu leuwih ti 10mm (0,4 inci).

Kalayan rel transversal

Tanpa rel transversal atanapi rel anu jejeg pigura sisi panjang

Kalayan sistem sisipan

Dipasang ku baud

• modul kudu napel na dirojong ku opat bolts stainless steel M8 ngaliwatan liang ningkatna dituduhkeun dina bar transversal. Torsi dina clamp bolt has to be in range of 8÷10 Nm (5,9÷7,38 ft-lb). The transversal bars positioning is shown in Figure 3.
• If additional mounting points are required, depending on the local wind and snow loads, then a mounting solution with clamphardware kudu dipilih.

• Mounting with bolts can be done only through dedicated predrilled holes in the frame.
• Pangeboran liang anyar dilarang sarta bakal batal jaminan.

POSISI kotak simpang

• Pikeun jarak antara kotak simpang jeung ujung modul atawa dimensi séjén tina posisi kotak simpang jeung wewengkon mangga tingal inohong ditémbongkeun di handap.

NGAJAGA

• Pikeun mastikeun kinerja modul anu optimal, SoliTek nyarankeun ieu:
• Upami diperlukeun, kaca hareup modul bisa cleaned kalawan cai sarta bolu lemes atawa lawon.
• A hampang, deterjen non-abrasive bisa dipaké pikeun miceun noda leuwih nekad.
• Pariksa sambungan listrik sarta mékanis périodik tur pastikeun aranjeunna bersih, aman, lengkep jeung aman.
• Upami aya masalah, konsultasi sareng jalma anu dilisensikeun / mumpuni.

SPESIFIKASI

Table 9. Electrical and mechanical parameters table.

Table 10. Electrical and mechanical parameters table.

Table 11.Electrical and mechanical parameters table.

• The electrical characteristics are within of the indicated values of ISC (φISC) ±3%, VOC (ϕVOC) ±3,5% and PMPP (ϕPmax) ±5%, under Standard Test Conditions (STC) (irradiance of 1000 W/m²,AM 1.5 spectrum, and a cell temperature of 25°C / 77°F)
• Sadaya panel SoliTek SOLID PV pakait sareng kelas kaamanan listrik II.

Bantahan tina liability

• Kusabab mustahil pikeun SoliTek ngadalikeun pamasangan, operasi, aplikasi sareng pangropéa sistem photovoltaic nurutkeun parentah ieu. SoliTek teu narima tanggung jawab jeung dinyatakeun disclaims liability pikeun sagala leungitna, karuksakan atawa expense timbul tina atawa sagala cara disambungkeun jeung instalasi, operasi, pamakéan atawa perawatan misalna.
• SoliTek will not take any responsibility for any possible violation of patent rights and third-party rights that are related to the application of the solar energy system. No permission of patents is given through implication.
• The information of this instruction is from the knowledge and experiences of SoliTek. However, the instructions and suggestions of this instruction do not make an external or internal of guarantee. SoliTek reserves the right to revise this instruction, products and all the information about products without prior notification to customers.

www.solitek.eu

FAQ

• Q: What should I do before installing the PV modules?
  • A: Read this entire guide, understand all instructions, and ensure compliance with all local, state, and federal regulations. Consult a certified building specialist for the structural integrity of the dwelling.
• Q: Can I install the PV modules myself without professional training?
  • A: This documentation is not a complete installation manual for personnel not specifically trained in PV-modules. It serves as a general but strictly mandatory reference for the installer. Professional installation is highly recommended.
• Q: What happens if I don’t follow the instructions in this guide?
  • A: Failure to follow instructions may damage system components, endanger personnel, damage property, or invalidate the panel warranty.
• Q: Is it safe to work on a rooftop during installation?
  • A: Do not attempt to work on a rooftop until safety precautions have been identified and taken, including fall protection measures, ladders or stairways, and personal protective equipment (PPE). Avoid adverse conditions like strong winds or wet/frosted roofs.
• Q: How should I store the PV modules before installation?
  • A: Store pallets in a cool and dry location until the PV modules are ready to be unpackaged. Do not exceed the maximum stacking height indicated on the packaging.